strain-induced martensite transformation simulations during cold rolling of aisi 301 austenitic stainless steel

نویسندگان

m. imaninezhad

department of biomedical engineering, saint louis university, saint louis, 63103, mo, usa t. yan

department of mechanical engineering, southern illinois university edwardsville, edwardsville, 62026, il usa a. najafizadeh

department of materials engineering, fould institue of technology, fould shahar, iran

چکیده

austenite is a semi-stable phase in most stainless steels that deforms to martensite under md30 and forms martensitetype ά and ε due to the deformation in the steels. since the distribution of strain induced martensite plays animportant role in achieving desired properties, the main objective of the present work is to model martensitedistribution of ά during cold rolling using finite element method and olsen-cohen model. in this study, thestrain induced martensite transformation of 301 stainless steel during cold rolling has been simulated by ansyssoftware. first, the mesh sensitivity analysis was performed and mesh optimization was set to stimulate the straininduced martensite transformation of 301 stainless steel during cold rolling. martensite fractions in cold-rollingwas simulated and compared with experimental data. finite element analysis was performed to obtain strain andstress during cold rolling. the amount and distribution of martensite during cold rolling has been modeled. thehighest stress level was observed and applied on a friction plate which was in contact with rollers and, as aresult, was under the most friction; thus, the stress reduced away from the surface toward the center of the sheet.moreover, a similar phenomenon was observed for changes in the strain. these results were also compared withexperimental data that had been obtained with x-ray diffraction, with the use of a ferritoscope, x-ray diffractionand experimental results.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Strain-Induced Martensite Transformation Simulations during Cold Rolling of AISI 301 Austenitic Stainless Steel

Austenite is a semi-stable phase in most stainless steels that deforms to martensite under Md30 and forms martensitetype ά and ε due to the deformation in the steels. Since the distribution of strain induced martensite plays animportant role in achieving desired properties, the main objective of the present work is to model martensitedistribution of ά during cold rolling using...

متن کامل

PHASE TRANSFORMATION DURING WEAR OF AISI STAINLESS STEEL 316

Abstract: Austenitic stainless steels exhibit a low hardness and weak tribological properties. The wear behaviour of austenitic stainless steel AISI 316 was evaluated through the pin on disc tribological method. For investigating the effect of wear on the changes in microstructure and resistance to wear, optical microscopy and scanning electron microscope were used. The hardness of the worn...

متن کامل

Martensite ? austenite phase transformation kinetics in an ultrafine-grained metastable austenitic stainless steel

A generalized phase transformation kinetics model is used to understand the martensite to austenite transformation in a cold-rolled and annealed metastable AISI 301LN ultrafine-grained austenitic stainless steel. The model shows that the presence of interstitial nitrogen and heavy cold-rolling is important to promote fast transformation kinetics, through rapid nitrogen-diffusion and austenite n...

متن کامل

Experimental Quantification of Phase Transformation in Austenitic Stainless Steel

This conference paper briefly discusses different techniques for measuring the evolution of the martensite content in cold-rolled stainless steel 301LN sheets under mechanical loading. Three methods are employed to measure the martensite content: (1) micrography, (2) bulk magnetic induction, and (3) local magnetic permeability measurements. The first two methods require the extraction of sample...

متن کامل

Influence of Annealing Treatment on the Formation of Nano/Submicron Grain Size AISI 301 Austenitic Stainless Steels

Nano/submicron austenitic stainless steels have attracted increasing attention over the past few years due to fine structural control for tailoring engineering properties. At the nano/submicron grain scales, grain boundary strengthening can be significant, while ductility remains attractive. To achieve a nano/ submicron grain size, metastable austenitic stainless steels are heavily cold-worked,...

متن کامل

Crystallographic Analysis of Lath Martensite in Ferrite-Martensite Dual Phase Steel Sheet Annealed after Cold-Rolling

The martensite steels produced by quenching and tempering has been used for machine structural use. Martensite in ferrite-martensite dual-phase steels (hereinafter, DP steels) also has important roll in strengthening of the automobile steel sheets. Therefore the importance of analyzing the microstructure and their mechanical properties of the martensite has been increased year by year. Many res...

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید


عنوان ژورنال:
international journal of iron and steel society of iran

جلد ۱۳، شماره ۲، صفحات ۲۶-۳۰

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023