In situ TiC–Fe–Al2O3–TiAl/Ti3Al composite coating processing using centrifugal assisted combustion synthesis
نویسندگان
چکیده
1359-8368/$ see front matter 2013 Elsevier Ltd. All rights reserved. http://dx.doi.org/10.1016/j.compositesb.2013.12.016 ⇑ Corresponding author at: Centre of Advanced Manufacturing and Materials Processing (AMMP), Department of Mechanical Engineering, University of Malaya, 50603 Kuala Lumpur, Malaysia. Tel.: +60 (3)79675200; fax: +60 (3)79675330. E-mail addresses: [email protected] (R. Mahmoodian), hamdi@ um.edu.my (M. Hamdi), [email protected] (R.G. Rahbari). Reza Mahmoodian a,d,⇑, M.A. Hassan , M. Hamdi , R. Yahya , R.G. Rahbari c
منابع مشابه
Modified smoothed particle hydrodynamics (MSPH) for the analysis of centrifugally assisted TiC-Fe-Al2O3 combustion synthesis
A modified smoothed particle hydrodynamic (MSPH) computational technique was utilized to simulate molten particle motion and infiltration speed on multi-scale analysis levels. The radial velocity and velocity gradient of molten alumina, iron infiltration in the TiC product and solidification rate, were predicted during centrifugal self-propagating high-temperature synthesis (SHS) simulation, wh...
متن کاملPRODUCTION OF TiAl/Al2O3 AND TiAl/Ti2AlC/Al2O3 COMPOSITES BY EXPLOSION SYNTHESIS
Thermal explosion mode of combustion synthesis was used to fabricate TiAl-Al2O3 and TiAl-Ti2AlC-Al2O3 composites from elemental powder mixtures of TiO2, Al and C and characterized by XRD and Scanning Electron Microscopy (SEM) coupled with Energy-Dispersive Spectroscopy (EDS). The experimental results showed that thermite reaction of Al with TiO2 caused TiAl-Al2O3 composite formation. By adding ...
متن کاملNUMERICAL MODELING OF THE COMBUSTION SYNTHESIS OF TiAl/Al2O3 COMPOSITE VIAMICROWAVE HEATING
Abstract: Microwave processing is one of the novel methods for combustion synthesis of intermetallic compounds andcomposites. This method brings about a lot of opportunities for processing of uniquely characterized materials. In thisstudy, the combustion synthesis of TiAl/Al2O3 composite via microwave heating has been investigated by thedevelopment of a heat transfer model including a microwave...
متن کاملThe Effect of Raw Material Ratios on the Fe-TiC/Al2O3 Composite Formation Mechanism
Ilmenite, aluminum and graphite can be used to produce in-situ Al2O3/TiC–Fe composites which are used as cutting tools. Few publications can be found in the literature that discusse the effect of molar ratio of aluminum and graphite on the Al2O3/TiC–Fe formation mechanism. Therefore, the present research is designed to make the issue clear. To achieve this goal, at first, the mechanism o...
متن کاملPREPARATION OF NANO-STRUCTURAL Al2O3-TiB2 IN-SITU COMPOSITE USING MECHANICALLY ACTIVATED COMBUSTION SYNTHESIS FOLLOWED BYINTENSIVE MILLING
Abstract: Nano-structural synthesized materials can be fabricated utilizing intensive milling after combustion synthesis. The Al2O3-TiB2 ceramic composite has been synthesized by aluminothermic reactions between Al, Ti (TiO2), and B (B2O3 or H3BO3). Boric acid (H3BO3) is less expensive than boron oxide, and after being dehydrated at 200°C, boron oxide will be obtained. In this study, Al, TiO2, ...
متن کامل