Холодне прокатування алюмінієвого сплаву системи AL-MG
نویسندگان
چکیده
Корева В. О. Холодне прокатування алюмінієвого сплаву системи AL-MG
 Алюмінієві зварювані та термічно не зміцнювальні сплави Al-Mg широко використовуються в якості легких конструкційних матеріалів різноманітних галузях промисловості. Покращення питомих міцнісних характеристик таких сплавів за рахунок холодної пластичної деформації є однією із актуальних науково-технічних проблем. Проте важливим питанням при розробці технологічних режимів формозміни алюмінієвих також прогнозування руйнування, яке супроводжується розвитком збільшенням кількості мікропор мікротріщин. В роботі виконано дослідження деформаційної обробки холодним прокатуванням. Чисельне моделювання процесу холодного 5056 виконували методом скінченних елементів використанням програмного комплексу для інженерного аналізу операцій металів тиском DEFORM-3D. результаті чисельного експерименту було отримано графік моментів, що виникають на валках. Також розподіли напружень (інтенсивності середніх осередку деформування,) максимальному моменті валках деформацій інших компонентів) кінці деформування. Проведений аналіз накопичення пошкоджуваності, встановлено моделюванням. даній чисельному моделюванні пошкоджуваність металу розраховували по критерію руйнування Cockroft & Latham. наведені результати експериментальних досліджень, тому числі мікроструктури, після проведеного прокатування. Встановлено, отримуємо зерно довжиною 100…200 мкм шириною 10…20 мкм.
منابع مشابه
FRACTIONAL RECRYSTALLIZATION KINETICS IN DIRECTLY COLD ROLLED Al-Mg, Al-Mg-Sc AND Al-Mg-Sc-Zr ALLOY
The evaluation of texture as a function of recrystallization has been characterized for directly cold rolled Al-6Mg, Al-6Mg-0.4Sc and Al-6Mg-0.4Sc-0.2Zr alloys. Samples were annealed isothermally at 400 °C for 1 to 240 minutes to allow recrystallization. Recrystallization kinetics of the alloys is analyzed from the micro-hardness variation. Isothermally annealed samples of aluminum alloys were ...
متن کاملMg isotopic heterogeneity, Al-Mg isochrons, and canonical Al ⁄Al in the early solar system
There is variability in the Mg isotopic composition that is a reflection of the widespread heterogeneity in the isotopic composition of the elements in the solar system at approximately 100 ppm. Measurements on a single calcium-aluminum-rich inclusion (CAI) gave a good correlation of Mg ⁄ Mg with Al ⁄ Mg, yielding an isochron corresponding to an initial (Al ⁄ Al)o = (5.27 ± 0.18) · 10 and an in...
متن کاملTHERMAL ANALYSIS AND KINETICS OF THE PRECIPITATION IN WROUGHT Al-Mg, Al-Mg-ScAND Al-Mg-Sc-Me (Me=Zr, Ti) ALLOYS
Precipitation behaviour of wrought Al-6Mg alloys with ternary scandium and quaternary zirconium and titanium has been studied. Hardness measurements and resistivity studies are employed to assess the precipitation behaviour of scandium doped Al-6Mg alloy without or with quaternary additions of zirconium and titanium. Further, the kinetics of precipitations are studied by differential scanning c...
متن کاملStudy on Mg/Al Weld Seam Based on Zn–Mg–Al Ternary Alloy
Based on the idea of alloying welding seams, a series of Zn-xAl filler metals was calculated and designed for joining Mg/Al dissimilar metals by gas tungsten arc (GTA) welding. An infrared thermography system was used to measure the temperature of the welding pool during the welding process to investigate the solidification process. It was found that the mechanical properties of the welded join...
متن کاملEthane dehydrogenation on Pt/Mg(Al)O and PtSn/Mg(Al)O catalysts
0021-9517/$ see front matter 2010 Elsevier Inc. A doi:10.1016/j.jcat.2010.01.016 * Corresponding author. Fax: +1 510 642 4778. E-mail address: [email protected] (A.T. Bel The dehydrogenation of ethane to ethene on Sn-promoted Pt supported on calcined hydrotalcite, PtSn/ Mg(Al)O, was investigated with the aim of understanding the effects of Sn on the local environment of the dispersed Pt, ...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: Obrabotka materialov davleniem
سال: 2022
ISSN: ['2076-2151']
DOI: https://doi.org/10.37142/2076-2151/2022-1(51)147