Design, Microstructure and Mechanical Properties of Cast Medium Entropy Aluminium Alloys
نویسندگان
چکیده
منابع مشابه
Influence of heat treatment on the microstructure and mechanical properties of 6005 and 6082 aluminium alloys
The main task of this work was to study the influence of the cooling conditions after homogenization of the 6082 aluminium alloys. The effect of the solution heat treatment temperature on the mechanism and ageing kinetics of the two commercial wrought aluminum alloys 6005 and 6082 was also analyzed. The alloys were heat treated—T4 with a wide range of solution heat treatment temperature from 51...
متن کاملdetermination of some physical and mechanical properties red bean
چکیده: در این تحقیق، برخی خواص فیزیکی و مکانیکی لوبیا قرمز به-صورت تابعی از محتوی رطوبت بررسی شد. نتایج نشان داد که رطوبت بر خواص فیزیکی لوبیا قرمز شامل طول، عرض، ضخامت، قطر متوسط هندسی، قطر متوسط حسابی، سطح تصویر شده، حجم، چگالی توده، تخلخل، وزن هزار دانه و زاویه ی استقرار استاتیکی در سطح احتمال 1 درصد اثر معنی داری دارد. به طوری که با افزایش رطوبت از 54/7 به 12 درصد بر پایه خشک طول، عرض، ضخام...
15 صفحه اولMechanical properties and grindability of dental cast Ti-Nb alloys.
Aiming at developing a dental titanium alloy with better mechanical properties and machinability than unalloyed titanium, a series of Ti-Nb alloys with Nb concentrations up to 30% was made. They were cast into magnesia-based molds using a dental casting machine and the mechanical properties and grindability of the castings were examined. The hardness of the alloys with Nb concentrations of 5% a...
متن کاملThe Microstructure and Mechanical Properties of Refractory High-Entropy Alloys with High Plasticity
Refractory high-entropy alloys (RHEAs) are promising materials used at high temperature, but their low plasticity restricts their application. Based on the valence electron concentration (VEC) principle, four kinds of RHEAs (ZrTiHfV0.5Nb0.5, Zr2.0TiHfVNb2.0, ZrTiHfNb0.5Mo0.5, and ZrTiHfNb0.5Ta0.5) are designed (VEC < 4.5). The experimental results show that the plasticity of these alloys was gr...
متن کاملMicrostructure, Mechanical and Tribological Properties of Oxide Dispersion Strengthened High-Entropy Alloys
A novel metal matrix composite CrMnFeCoNi with Y₂O₃ as reinforcement phase was designed and manufactured by mechanical alloying and spark plasma sintering. After sintering at 900 °C for 5 min, the microstructure consisted of a FCC matrix and Y₂O₃ nanoparticles. The addition of 0.25 wt % Y₂O₃ increased the room temperature tensile strength of the CrMnFeCoNi base from 868 MPa to 1001 MPa, while t...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: Scientific Reports
سال: 2019
ISSN: 2045-2322
DOI: 10.1038/s41598-019-43329-w