Fabrication of CrSi2 Thermoelectric Material Using Mechanical Alloying.

نویسندگان
چکیده

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Thermoelectric performance of lanthanum telluride produced via mechanical alloying

Andrew F. May,1 Jean-Pierre Fleurial,2 and G. Jeffrey Snyder3 1Department of Chemical Engineering, California Institute of Technology, 1200 East California Boulevard, Pasadena, California 91125, USA 2Jet Propulsion Laboratory, California Institute of Technology, 4800 Oak Grove Drive, Pasadena, California 91109, USA 3Department of Materials Science, California Institute of Technology, 1200 East ...

متن کامل

Fabrication of TiC particulate reinforced Ni-50Fe super alloy matrix composite powder by mechanical alloying

Mechanical alloying is a powder metallurgy processing technique involving cold welding, fracturing, and rewelding of powder particles in a high-energy ball mill. In this work, NiFe-TiC composite powders were prepared by mechanical alloying process using planetary high-energy ball mill. The effect of TiC addition by weight percent on the NiFe solid solution formation, grain size, lattice paramet...

متن کامل

Thermoelectric Performance of Micro/Nano-Structured Bismuth-Antimony-Telluride Bulk from Low Cost Mechanical Alloying

In this work, micro/nano-structured Bi0.5Sb1.5Te3 bulk thermoelectric materials were synthesized by mechanical alloying from elemental shots of Bi, Sb, and Te. Cold pressing and subsequent heat treatments with hydrogen reduction were used to form bulk solid samples with good thermoelectric properties in the temperature range around 75 ̊C to 100 ̊C. In comparison to crystal growth methods and chem...

متن کامل

Thermoelectric Properties of Alumina-Doped Bi0.4Sb1.6Te3 Nanocomposites Prepared through Mechanical Alloying and Vacuum Hot Pressing

In this study, γ-Al2O3 particles were dispersed in p-type Bi0.4Sb1.6Te3 through mechanical alloying to form γ-Al2O3/Bi0.4Sb1.6Te3 composite powders. The composite powders were consolidated using vacuum hot pressing to produce nanoand microstructured composites. Thermoelectric (TE) measurements indicated that adding an optimal amount of γ-Al2O3 nanoparticles improves the TE performance of the fa...

متن کامل

Thermoelectric SnS and SnS-SnSe solid solutions prepared by mechanical alloying and spark plasma sintering: Anisotropic thermoelectric properties

P-type SnS compound and SnS1-xSex solid solutions were prepared by mechanical alloying followed by spark plasma sintering (SPS) and their thermoelectric properties were then studied in different compositions (x = 0.0, 0.2, 0.5, 0.8) along the directions parallel (//) and perpendicular (⊥) to the SPS-pressurizing direction in the temperature range 323-823 Κ. SnS compound and SnS1-xSex solid solu...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

ژورنال

عنوان ژورنال: Journal of the Japan Society of Powder and Powder Metallurgy

سال: 2002

ISSN: 0532-8799,1880-9014

DOI: 10.2497/jjspm.49.996