Mechanical properties of polyurethane/montmorillonite nanocomposite prepared by melt mixing
نویسندگان
چکیده
منابع مشابه
Influence of Homogenization on Mechanical Properties of Al-1Mn-1Mg Alloy Prepared by Different Melt-Treatments
Influence of homogenization on mechanical properties of Al-1Mn-1Mg alloy prepared by different melttreatments was discussed and mechanism of metallurgical defects on ingots’ mechanical properties was analyzed. It was found that metallurgical defects, such as the inclusions and gas holes, cannot be removed from the original ingots by homogenization; the average increasement of tensile strength o...
متن کاملcontrol of the optical properties of nanoparticles by laser fields
در این پایان نامه، درهمتنیدگی بین یک سیستم نقطه کوانتومی دوگانه(مولکول نقطه کوانتومی) و میدان مورد مطالعه قرار گرفته است. از آنتروپی ون نیومن به عنوان ابزاری برای بررسی درهمتنیدگی بین اتم و میدان استفاده شده و تاثیر پارامترهای مختلف، نظیر تونل زنی(که توسط تغییر ولتاژ ایجاد می شود)، شدت میدان و نسبت دو گسیل خودبخودی بر رفتار درجه درهمتنیدگی سیستم بررسی شده اشت.با تغییر هر یک از این پارامترها، در...
15 صفحه اولdetermination of some physical and mechanical properties red bean
چکیده: در این تحقیق، برخی خواص فیزیکی و مکانیکی لوبیا قرمز به-صورت تابعی از محتوی رطوبت بررسی شد. نتایج نشان داد که رطوبت بر خواص فیزیکی لوبیا قرمز شامل طول، عرض، ضخامت، قطر متوسط هندسی، قطر متوسط حسابی، سطح تصویر شده، حجم، چگالی توده، تخلخل، وزن هزار دانه و زاویه ی استقرار استاتیکی در سطح احتمال 1 درصد اثر معنی داری دارد. به طوری که با افزایش رطوبت از 54/7 به 12 درصد بر پایه خشک طول، عرض، ضخام...
15 صفحه اولInvestigation on Mechanical and Electrical Properties of Cu-Ti Nanocomposite Produced by Mechanical Alloying
In this paper, Cu-Ti nanocomposite synthesized via ball milling of copper-titanium powders in 1, 3, and 6 of weight percentage compounds. The vial speed was 350 rpm and ball to powder weight ratio kept at 15:1 under Argon atmosphere, and the time of milling was 90 h. Obtained powders were studied by scanning electron microscopy (SEM), X-ray diffraction (XRD), and dynamic light scattering (DLS)....
متن کاملManufacture and Mechanical Properties of Nanocomposite Laminates
This work mainly aims to manufacture nanocomposite laminates at first. The prepreg AS-4 graphite/PolyEtherEtherKetone laminates were used to make a 16-layered APC-2 laminate of 2 mm thick via curing the modified diaphragm. The nanoparticles of Silica (SiO2) were uniformly spread on the specific interfaces totally about 1-3% by weight of a laminate by sol-gel method. Second, by the results of me...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: Journal of Applied Polymer Science
سال: 2007
ISSN: 0021-8995,1097-4628
DOI: 10.1002/app.26721