Mechanical Quality Factor of Pb(Zr<i><sub>x</sub></i>Ti <sub>1−</sub><i><sub>x</sub></i>) <sub>1−</sub><i><sub>y</sub></i> (Mg<sub>1/3</sub>Nb<sub>2/3</sub>)<i><sub>y</sub></i>O<sub>3</sub> Solid Solution Prepared by Wet-Dry Combination Method
نویسندگان
چکیده
منابع مشابه
Dry and Wet Wear Characteristic of TiO2 Thin Film Prepared by Magnetic Sputtering in Ringer Solution
In this research, a thin film of TiO2 was applied on AZ91D using the method of magnetic sputtering. Microstructure investigations were done using field emission scanning electron microscope (FESEM) and X-ray diffraction (XRD). Wear resistance for the coating was investigated using the pin on the disk in the form of dry and in the Ringer's solution. After this test, the worn surface of the sampl...
متن کاملsolution of security constrained unit commitment problem by a new multi-objective optimization method
چکیده-پخش بار بهینه به عنوان یکی از ابزار زیر بنایی برای تحلیل سیستم های قدرت پیچیده ،برای مدت طولانی مورد بررسی قرار گرفته است.پخش بار بهینه توابع هدف یک سیستم قدرت از جمله تابع هزینه سوخت ،آلودگی ،تلفات را بهینه می کند،و هم زمان قیود سیستم قدرت را نیز برآورده می کند.در کلی ترین حالتopf یک مساله بهینه سازی غیر خطی ،غیر محدب،مقیاس بزرگ،و ایستا می باشد که می تواند شامل متغیرهای کنترلی پیوسته و گ...
Dry Wear Behavior of 42CrMo4 Steel/ZrO2 Composite Prepared by Pressure-Less Infiltration Method
The aim of this research was to study the wear behavior of 42CrMo4 steel/ZrO2 composite with 10 and 30 ppi performed ceramic and compare it with the un-reinforced steel under different applied loads. The composite specimens were obtained by pressureless infiltration of the melt into a preformed ceramic of zirconium oxide. The effect of applied load on the specimens wear behavior was ...
متن کاملPatterning PDMS using a combination of wet and dry etching
PDMS films of 10 μm thickness can be patterned within 30 min by combining dry etching to achieve substantially vertical sidewalls with wet etching to achieve high etch rates and to protect the underlying substrate from attack. Dry etching alone would have taken 5 h, and wet etching alone would produce severe undercutting. In addition, using either technique alone produces undesirable surface mo...
متن کاملWhite organic light-emitting diodes prepared by a fused organic solid solution method
This letter demonstrates a white organic light-emitting diode sOLEDd with high color stability fabricated by using a single organic white-emitting layer. The dopants were introduced prior to the device fabrication process through organic solid solution process formed by high-temperature and high-pressure fusion process. A high band gap organic material, a-naphthlyphenylbiphenyl diamine, was ado...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: Electrochemistry
سال: 1999
ISSN: 1344-3542,2186-2451
DOI: 10.5796/electrochemistry.67.985