Rate dependent fracture along a silicon/epoxy interface under mixed-mode loading conditions
نویسندگان
چکیده
This paper describes the development of a dual-actuator loading device that was then used to apply asymmetric, transverse end-displacements laminated beam specimens (silicon/epoxy/silicon) over range separation rates. Measurements reaction forces, as well load-point displacements and rotations, were determine normal tangential components crack tip corresponding J-integral. made possible because identically satisfied balance condition. The resulting data set obtained from experiments conducted at five rates each mode-mix phase angles is testimony efficiency approach. A mixed-mode on elastic foundation analysis established stiffness shear interactions silicon/epoxy interface independent rate mode-mix. Furthermore, values thus determined considerably lower than those based bulk behavior epoxy in tension shear. also allowed growth be tracked order establish its onset critical J-integral, along with strengths displacements. For mode-mix, these increased rate. increase properties spite glassy nature further suggests presence an interphase region adjacent silicon. However, change accompanied by local rates, leading non-monotonic Following growth, application radial paths resulted simultaneous changes implying fracture criterion depends both rate-dependent damage evolution processes.
منابع مشابه
Mixed Mode Fracture Analysis of Multiple Interface Cracks
This paper contains a theoretical formulation of multiple interface cracks in two bonded dissimilar half planes subjected to in-plane traction. The distributed dislocation technique is used to construct integral equations for a dissimilar mediums weakened by several interface cracks. These equations are of Cauchy singular type at the location of dislocation, which are solved numerically to obta...
متن کاملMixed Mode Loading of an Interface Crack Subjected to Creep Conditions
Interface cracks are seldom subjected to pure Mode I or pure Mode II conditions. Station~y interface cracks between two distinct, bonded elastic-creep materials subjected to remotely applied mixed mode loading are simulated. The finite element method (FEM) is used to examine crack tip fields and candidate driving force parameters for crack growth. Plane strain conditions are assumed. In most ca...
متن کاملRate-Dependent Fracture at Adhesive Interface
Schallamach’s theory of rate-dependent bond dissociation is used to understand the fracture of a polymerglass interface. The model system consists of an elastomeric film (20 μm thick) of poly(dimethylsiloxane), chemically bonded to a silanized glass substrate. The fracture energy of the interface varies logarithmically with velocity, which is consistent with Schallamach’s theory of forced bond ...
متن کاملExperimental investigation of mode I fracture energy of adhesively bonded joints under impact loading conditions
Background Recently, the automotive industry has paid attention to multi-material structures to reduce CO2 emission. Hence, the use of light-weight and high-strength materials such as Al–Mg alloys, high-tensile-strength steel and carbon-fiber-reinforced plastics (CFRP) is essential to lighten the vehicle weight [1]. Joining methods for these dissimilar materials are the key to apply them into t...
متن کاملFatigue strength evaluation of self-piercing riveted cold rolled steel joints under mixed mode loading conditions
Fatigue strength of cross-shaped specimens of SPR joints made of SPCC was evaluated at load angles of 0°, 45°, and 90°. For the static strength at load angles of 0°, 45°, and 90°, the maximum loads were determined to be 4890N, 1969N, and 1611N, respectively. Regarding for the relationship between the load amplitude and the number of cycles (Nf), the results were 014 . 0 3 . 2209 − = f amp N P ,...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: International Journal of Solids and Structures
سال: 2022
ISSN: ['1879-2146', '0020-7683']
DOI: https://doi.org/10.1016/j.ijsolstr.2021.111129