Study of 3D printing for forming spoke of non-pneumatic tire using finite element method
نویسندگان
چکیده
منابع مشابه
buckling of viscoelastic composite plates using the finite strip method
در سال های اخیر، تقاضای استفاده از تئوری خطی ویسکوالاستیسیته بیشتر شده است. با افزایش استفاده از کامپوزیت های پیشرفته در صنایع هوایی و همچنین استفاده روزافزون از مواد پلیمری، اهمیت روش های دقیق طراحی و تحلیل چنین ساختارهایی بیشتر شده است. این مواد جدید از خودشان رفتارهای مکانیکی ارائه می دهند که با تئوری های الاستیسیته و ویسکوزیته، نمی توان آن ها را توصیف کرد. این مواد، خواص ویسکوالاستیک دارند....
A study on behavior of block pavement using 3D finite element method
Three dimensioned finite element analysis were conducted on concrete block paving. In order to verify the calculated results, an experimental case study was analyzed. Good agreement was observed between the measured and the calculated results. Based on the finite element analysis results and available failure models, comprehensive design charts were developed for port and industrial pavement wh...
متن کاملmetrics for the detection of changed buildings in 3d old vector maps using als data (case study: isfahan city)
هدف از این تحقیق، ارزیابی و بهبود متریک های موجود جهت تایید صحت نقشه های قدیمی سه بعدی برداری با استفاده از ابر نقطه حاصل از لیزر اسکن جدید شهر اصفهان می باشد . بنابراین ابر نقطه حاصل از لیزر اسکنر با چگالی حدودا سه نقطه در هر متر مربع جهت شناسایی عوارض تغییر کرده در نقشه های قدیمی سه بعدی استفاده شده است. تمرکز ما در این تحقیق بر روی ساختمان به عنوان یکی از اصلی ترین عارضه های شهری می باشد. من...
stress analysis of tractor tire interaction whit soft soil using non-linear 2d finite element method
abstract: compaction under tractors tires is of special concern because the weight of these machines has increased dramatically in the last years. these machines and others associated with crop cultural practices weight enough to significantly compact the soil, especially if the soil is soft with high moisture content during tilling, planting, or harvesting. the stress distribution and the size...
متن کاملEvaluation of Disc Cutter Performance in Rock Cutting Process Using 3D Finite Element Method
Today, numerical simulation can be used as a suitable tool to measure large quantities that are very expensive and, in some cases, impossible to measure. One of the important issues in predicting rock mass boreability in excavation with full face tunnel boring machines is estimating the discchr('39')s forces for rock cutting. For this purpose, the linear cutting test is employed. However, limi...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
ژورنال
عنوان ژورنال: IOP Conference Series: Materials Science and Engineering
سال: 2021
ISSN: 1757-8981,1757-899X
DOI: 10.1088/1757-899x/1137/1/012020