dry wear behavior of 42crmo4 steel/zro2 composite prepared by pressure-less infiltration method

نویسندگان

h. sharifi

department of materials science, faculty of engineering, shahrekord university, shahrekord, iran m. salehi

department of materials engineering, isfahan university of technology, isfahan, iran t. dallali isfahani

department of materials science and engineering, golpayegan university of technology, golpayegan, iran h. rafiei borujeni

department of materials science, faculty of engineering, shahrekord university, shahrekord, iran

چکیده

the aim of this research was to study the wear behavior of 42crmo4 steel/zro2 composite with 10 and 30 ppi performed ceramic and compare it with the un-reinforced steel under different applied loads. the composite specimens were obtained by pressureless infiltration of the melt into a preformed ceramic of zirconium oxide. the effect of applied load on the specimens wear behavior was studied by applying the wear test under loads of 90, 120 and 150 (n). the results indicated that at the applied loads, the reinforcement and the increase of volume fraction considerably improved the specimens wear behavior. furthermore, the microscopic images showed that the increase in force resulted in a change in the wear mechanism of the steel and the 10ppi composite from an abrasive to an adhesive one, while the wear mechanism of the 30ppi composite remained unchanged as abrasive.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Dry Wear Behavior of 42CrMo4 Steel/ZrO2 Composite Prepared by Pressure-Less Infiltration Method

The aim of this research was to study the wear behavior of 42CrMo4 steel/ZrO2 composite with 10 and 30 ppi performed ceramic and compare it with the un-reinforced steel under different applied loads. The composite specimens were obtained by pressureless infiltration of the melt into a preformed ceramic of zirconium oxide. The effect of applied load on the specimens wear behavior was ...

متن کامل

Dry and Wet Wear Characteristic of TiO2 Thin Film Prepared by Magnetic Sputtering in Ringer Solution

In this research, a thin film of TiO2 was applied on AZ91D using the method of magnetic sputtering. Microstructure investigations were done using field emission scanning electron microscope (FESEM) and X-ray diffraction (XRD). Wear resistance for the coating was investigated using the pin on the disk in the form of dry and in the Ringer's solution. After this test, the worn surface of the sampl...

متن کامل

Dry Sliding Wear and Mechanical Behavior of Aluminium / Fly ash / Graphite Hybrid Metal Matrix Composite Using Taguchi Method

The experimental investigation of hybrid metal matrix composites with fly ash and graphite reinforced aluminium alloy (Al 6061) composites samples, processed by stir casting route are reported. The aluminium alloy was reinforced with 3 wt.%, 6 wt.%, 9 wt.% fly ash and fixed 3 wt.% of graphite to mixture the hybrid composite. Hardness of the hybrid composite were tested it was found that when th...

متن کامل

Wear Behavior of Aluminium Metal Matrix Composite Prepared from Industrial Waste

With an increase in the population and industrialization, a lot of valuable natural resources are depleted to prepare and manufacture products. However industrialization on the other hand has waste disposal issues, causing dust and environmental pollution. In this work, Aluminium Metal Matrix Composite is prepared by reinforcing 10 wt% and 20 wt% of wet grinder stone dust particles an industria...

متن کامل

Microstructure and Dry-Sliding Wear Behavior of B4C Ceramic Particulate Reinforced Al 5083 Matrix Composite

B4C ceramic particulate–reinforced Al 5083 matrix composite with various B4C content was fabricated successfully via hot-press sintering under Argon atmosphere. B4C particles presented relative high wettability, bonding strength and symmetrical distribution in the Al 5083 matrix. The hardness value, friction coefficient and wear resistance of the composite were higher than those of the Al 5083 ...

متن کامل

buckling of viscoelastic composite plates using the finite strip method

در سال های اخیر، تقاضای استفاده از تئوری خطی ویسکوالاستیسیته بیشتر شده است. با افزایش استفاده از کامپوزیت های پیشرفته در صنایع هوایی و همچنین استفاده روزافزون از مواد پلیمری، اهمیت روش های دقیق طراحی و تحلیل چنین ساختارهایی بیشتر شده است. این مواد جدید از خودشان رفتارهای مکانیکی ارائه می دهند که با تئوری های الاستیسیته و ویسکوزیته، نمی توان آن ها را توصیف کرد. این مواد، خواص ویسکوالاستیک دارند....

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید


عنوان ژورنال:
international journal of iron and steel society of iran

جلد ۱۳، شماره ۱، صفحات ۸-۱۴

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023