enhanced procedure for fabrication of an ultrahydrophobic aluminum alloy surface using fatty acid modifiers

نویسندگان

mehrdad fallahah

faculty of polymer science, iran polymer and petrochemical institute, p.o. box 14965-115, tehran, iran ahmad rabiee

faculty of polymer science, iran polymer and petrochemical institute, p.o. box 14965-115, tehran, iran mohammad ghashghaee

iran polymer and petrochemical institute amir ershad-langroudi

faculty of polymer processing, iran polymer and petrochemical institute, p.o. box 14965-115, tehran, iran

چکیده

a superhydrophobic aluminum surface was fabricated through an enhanced low-cost approach and the effects of several relevant factors on static contact angle and sliding angle were investigated. first, the operating parameters including the etching time as well as the reaction time and temperature were varied. next, the so-called chemical factors including three different fatty acids and five different solvents were examined. the surface was analyzed by means of sem, atr-ftir, edx, and wca measurements. the results show that the immersion time of about 5 min and the reaction temperature of about 60 °c were the optimum conditions for the creation of a superhydrophobic al surface with excellent self-cleaning properties. overall, the choice of oleic acid and ethanol were found to be the best as the fatty acid and solvent, respectively. the highest contact angle was 163.7° and the lowest sliding angle was about 1°.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Enhanced Procedure for Fabrication of an Ultrahydrophobic Aluminum Alloy Surface using Fatty Acid Modifiers

A superhydrophobic aluminum surface was fabricated through an enhanced low-cost approach and the effects of several relevant factors on static contact angle and sliding angle were investigated. First, the operating parameters including the etching time as well as the reaction time and temperature were varied. Next, the so-called chemical factors including three different fatty acids and five di...

متن کامل

Fabrication of Aluminum Tubes Filled with Aluminum Alloy Foam by Friction Welding

Aluminum foam is usually used as the core of composite materials by combining it with dense materials, such as in Al foam core sandwich panels and Al-foam-filled tubes, owing to its low tensile and bending strengths. In this study, all-Al foam-filled tubes consisting of ADC12 Al-Si-Cu die-cast aluminum alloy foam and a dense A1050 commercially pure Al tube with metal bonding were fabricated by ...

متن کامل

Enhanced mixing in laminar flows using ultrahydrophobic surfaces.

Under laminar, microscale flow conditions, rapid mixing can be difficult to achieve. In these low Reynolds number flows, mixing rates are governed by molecular diffusion, and in the absence of enhanced mixing techniques, mixing lengths and residence times can be much longer than most applications will allow. A number of active mixing techniques have been developed to improve mixing; however, th...

متن کامل

an application of fuzzy logic for car insurance underwriting

در ایران بیمه خودرو سهم بزرگی در صنعت بیمه دارد. تعیین حق بیمه مناسب و عادلانه نیازمند طبقه بندی خریداران بیمه نامه براساس خطرات احتمالی آنها است. عوامل ریسکی فراوانی می تواند بر این قیمت گذاری تاثیر بگذارد. طبقه بندی و تعیین میزان تاثیر گذاری هر عامل ریسکی بر قیمت گذاری بیمه خودرو پیچیدگی خاصی دارد. در این پایان نامه سعی در ارائه راهی جدید برای طبقه بندی عوامل ریسکی با استفاده از اصول و روش ها...

Low temperature formation Silver-Copper alloy nanoparticles using hydrogen plasma treatment for fabrication of humidity sensor

In this paper, a novel method of producing bi-metallic alloy nanoparticles at low temperatures using hydrogen bombardment of thin films, deposited on glass substrates, is introduced. Optical and morphological characteristics of the nanoparticles were extensively studied for various conditions of plasma treatment, such as plasma power density, temperature, duration of hydrogen bombardment, thick...

متن کامل

Low temperature formation Silver-Copper alloy nanoparticles using hydrogen plasma treatment for fabrication of humidity sensor

In this paper, a novel method of producing bi-metallic alloy nanoparticles at low temperatures using hydrogen bombardment of thin films, deposited on glass substrates, is introduced. Optical and morphological characteristics of the nanoparticles were extensively studied for various conditions of plasma treatment, such as plasma power density, temperature, duration of hydrogen bombardment, thick...

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید


عنوان ژورنال:
physical chemistry research

جلد ۵، شماره ۲، صفحات ۳۳۹-۳۵۷

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023