factors affecting weldability improvement of dissimilar welds of aged hp stainless steel and alloy 800

نویسندگان

r. dehmolaei

m. shamanian

a. kermanpur

چکیده

the microstructure of hp stainless steel in aged and aged + solution annealed conditions and solutionized alloy 800 was characterized by optical microscopy, scanning electron microscopy (sem), and transmission electron microscopy (tem) equipped by eds. all phases present in the above condition were described. the effects of solution annealing heat treatment temperature on the microstructure, tensile, hardness, toughness, and ductility of aged hp stainless steel and its weldability to alloy 800 have been discussed. in addition, the effects of heat input, interpass temperature, and type of filler metal on weldability of two alloys were investigated. it was found that during solution annealing, the precipitates produced in the aging stage are decomposed and niobium carbide (nbc) is formed. it was also observed that while tensile strength and hardness fell, ductility and toughness were improved. dissimilar welding between alloy 800 and aged hp stainless steel was not successful and cracks were observed in the haz of the aged hp stainless steel, while welding alloy 800 to hp stainless steel (aged + solution annealing at 1100-1200ºc, low interpass temperature, and inconel 82 or 617 filler metals) was successful.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Factors Affecting Weldability Improvement of Dissimilar Welds of Aged HP Stainless Steel and Alloy 800

The microstructure of HP stainless steel in aged and aged + solution annealed conditions and solutionized alloy 800 was characterized by optical microscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM) equipped by EDS. All phases present in the above condition were described. The effects of solution annealing heat treatment temperature on the microstructure, te...

متن کامل

AN EVALUATION OF THERMAL STABILITY IN DISSIMILAR WELDS BETWEEN 310 STAINLESS STEEL AND ALLOY 657

Abstract: The investigation is carried out to characterize welding of AISI 310 austenitic stainless steel to Inconel 657 nickel-chromium superalloy. The welds were produced using four types of filler materials: the nickel-based corresponding to Inconel 82, Inconel A, Inconel 617 and austenitic stainless steel 310. This paper describes the effects of aging treatment on the joint. The compara...

متن کامل

The Weldability Evaluation of Dissimilar Welds of AISI 347 Stainless Steel to ASTM A335 Low Alloy Steel by Gastungesten Arc Welding

In the present study, the Weldability and microstructure of dissimilar welds of AISI 347austenitic stainless steel to ASTM A335 low alloy steel was investigated. For this purpose, gas tungsten arc welding process and two filler metals including ERNICr-3 and ER309L were used. After welding, the microstructure of the different zones of each joint, including weld metals, heat affected zone (HAZ) 1...

متن کامل

The Evaluation of Corrosion Behavior of AISI 347 Stainless Steel to ASTM A335 Low Alloy Steel Dissimilar Welds

In the present study, the corrosion behavior of AISI 347 austenitic stainless steel to ASTM A335 low alloy steel dissimilar joint was investigated. For this purpose, two filler metals, ER309L and ERNiCr-3, were selected to be used during the gas tungsten arc welding process. To investigate the corrosion behavior of the joints after welding, the specimens were tested in 3.5% sodium chloride solu...

متن کامل

Investigation of microstructures and mechanical properties of dissimilar welds between Incoloy 825 and 316 stainless steel

In this study, microstructural features and mechanical properties of Incoloy 825-316L stainless steel dissimilar joints have been investigated. For this purpose, pulsed gas tungsten arc welding method was employed and 316L, Inconel 82 and Inconel 625 alloys were used as filler metal. First, specimens were cut. Pulsed gas tungsten arc welding was performed using peak and base currents of 220 A a...

متن کامل

Investigation of microstructures and mechanical properties of dissimilar welds between Incoloy 825 and 316 stainless steel

In this study, microstructural features and mechanical properties of Incoloy 825-316L stainless steel dissimilar joints have been investigated. For this purpose, pulsed gas tungsten arc welding method was employed and 316L, Inconel 82 and Inconel 625 alloys were used as filler metal. First, specimens were cut. Pulsed gas tungsten arc welding was performed using peak and base currents of 220 A a...

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید


عنوان ژورنال:
international journal of iron & steel society of iran

ناشر: iron & steel society of iran

ISSN 1735-4145

دوره 5

شماره 1 2008

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023