anisotropy in microalloyed s355n steel

نویسندگان

a. r. ebrahimi

a. abyazi

s. m. abbasi

چکیده

thermomechanical control process steel produced by rolling has a significant anisotropy. the elongated grains and inclusions formed during hot rolling of ferrite and low carbon hsla steels directly influence the anisotropy of the steel’s mechanical properties as a result of microstructural anisotropy. the present research deals with this anisotropy, and particular attention has been paid to the tensile and charpy v-notched behavior and microscopic properties. the mechanical response of a 25 mm thick rolled plate of s355n steel was characterized. the results of charpy tests of v-notched specimens of the through-thickness direction were found to be considerably temperature-dependent and also to vary in the longitudinal and the transverse directions. marked anisotropy effects were observed, with the through-thickness orientation exhibiting a tensile response lower than that of the longitudinal and transverse ones. these experimental findings were rationalized using the correlation holding among inclusion distribution, reduction area percent, and banding of the microstructure.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Anisotropy in Microalloyed S355N Steel

Thermomechanical control process steel <span style="font-family: 'Times New Roman','serif'; font-size: 10pt; mso-fareast-font-family: 'Times New Roman'; mso-bidi-language: AR-SA; m...

متن کامل

Process modeling of microalloyed steel for near net shape casting

Strip casting is an emerging technology for flat products; it is based on the concept of near-net shape casting; it holds potential for substantial energy saving and reduction in environmentally undesirable emission. In conventional thermo-mechanical processing, the pinning pressure due to the effects of Nb and NbC on boundary mobility is used to advantage to retard static recrystallisation and...

متن کامل

Effect of solidification rate on microstructure evolution in dual phase microalloyed steel

In steels the dependence of ambient temperature microstructure and mechanical properties on solidification rate is not well reported. In this work we investigate the microstructure and hardness evolution for a low C low Mn NbTi-microalloyed steel solidified in the cooling rate range of 1-50 Cs-1. The maximum strength was obtained at the intermediate solidification rate of 30 Cs-1. This result h...

متن کامل

Effect of austenitising and deformation temperatures on dynamic recrystallisation in Nb-Ti microalloyed steel

An investigation into influence of the austenitising temperature and the austenite deformation temperature on Nb precipitation and recrystallisation kinetics was carried out for a steel containing 0.081C-0.021Ti-0.064Nb (wt. %). The austenite grain structure was correlated to the dispersive properties of Nb atom clustering and precipitation. Irrespective of the austenitising temperature, deform...

متن کامل

Discussion on the Rate Controlling Process of Coarsening of Niobium Carbonitrides in a Niobium Microalloyed Steel

Austenite grain growth in microalloyed steels is governed by the coarsening of fine precipitates present at grain boundaries below the grain coarsening temperature. Zener model is widely used in metals to describe the pinning effect of second phase particles precipitated in the matrix. In this work it has been discussed whether grain boundary or volume diffusion is the rate controlling process ...

متن کامل

Isothermal Recrystallization Behavior of Cold-deformed Martensite in an Ultra-low-carbon Microalloyed Steel

One of the most promising ways to produce a grain-refined microstructure in some steel materials is the thermomechanical processing route of subcritical recrystallization annealing of a cold-deformed martensite structure. In the present study, the microstructural evolutions and the associated recrystallization kinetics under various subcritical annealing heat treatment conditions are explored i...

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید


عنوان ژورنال:
international journal of iron & steel society of iran

ناشر: iron & steel society of iran

ISSN 1735-4145

دوره 5

شماره 2 2008

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023