welding of 304l stainless steel with activated tungsten inert gas process (a-tig)

نویسندگان

e. ahmadi

a. r. ebrahimi

r. azari khosroshahi

چکیده

gas tungsten arc welding is a popular process in those applications requiring a high degree of quality andaccuracy. however, this process has a big disadvantage against the substantially high productivity weldingprocedures. hence, many efforts have been made to improve its productivity. one of these efforts is the use of activating flux (a-tig welding). in this study, the performance of a-tig welding on 304l austenitic stainless steel plates has been presented. two oxide fluxes, tio2 and sio2 were used to investigate the effect of a-tig welding process on weld morphology, microstructure and mechanical properties of weldments. the experimental results indicated that a-tig welding could increase the weld penetration and depth-to-wide ratio. it was also found that a-tig welding could increase the delta-ferrite content of weld metals and improve the mechanical properties. moreover, a 2d axial symmetric model was developed to simulate the flow behavior in the melting pool. these results were compared to those experiments carried out on a stainless steel (304l) melted by a stationary heat source.

برای دانلود باید عضویت طلایی داشته باشید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Welding of 304L Stainless Steel with Activated Tungsten Inert Gas Process (A-TIG)

Gas tungsten arc welding is a popular process in those applications requiring a high degree of quality and accuracy. However, this process has a big disadvantage against the substantially high productivity welding procedures. Hence, many efforts have been made to improve its productivity. One of these efforts is the use of activating flux (A-TIG welding). In this study, the performance of A-TIG...

متن کامل

The principle Of Tungsten Inert Gas (TIG) Welding Process

Process This chapter presents the principle of tungsten inert gas (TIG) welding process besides important components of TIG welding system and their role. This process is also known as gas tungsten arc welding (GTAW) process. Further, fundamentals of heat generation, arc stability and arc efficiency have also been described. Additionally, comparison of argon and helium as shielded gases has bee...

متن کامل

Structure-property Interaction in Flux Assisted Tungsten Inert Gas Welding of Austenitic Stainless Steel

Austenitic stainless steel SS304 grade was welded with active Tungsten Inert Gas (TIG) welding process by applying a flux paste made of SiO2 powder and acetone. SiO2 flux application improves the weld bead depth with a simultaneous reduction in weld bead width. The improvement in penetration results from arc constriction and reversal of Marangoni convection. Experimental studies revealed that t...

متن کامل

Optimization of Weld Bead Width in Tungsten Inert Gas Welding of Austenitic Stainless Steel Alloy

This paper investigates the effects of process parameters on weld bead width of austenitic stainless steel SS-310 in tungsten inert gas welding. The four parameters namely welding current, type of gas, gas flow rate and included angle of weld plates during butt joint were varied at three levels. The DOE approach was used to design experimental conditions. Orthogonal array L9 was used for carryi...

متن کامل

Characterization of Tungsten Inert Gas (TIG) Welding Fume Generated by Apprentice Welders

Tungsten inert gas welding (TIG) represents one of the most widely used metal joining processes in industry. Its propensity to generate a greater portion of welding fume particles at the nanoscale poses a potential occupational health hazard for workers. However, current literature lacks comprehensive characterization of TIG welding fume particles. Even less is known about welding fumes generat...

متن کامل

Welding of 304L Stainless Steel to 409 Stainless Steel with GMAW Process Using ER316LSi and ER309LMo Filler Metals

Dissimilar welding of AISI 304L austenitic stainless steel to AISI 409 ferritic stainless steel with GMAW process usingtwo Ar-O2 and Ar-CO2 shielding gas mixtures was studied. ER316LSi and ER309LMo filler metals were chosen by considering 5 and 15% delta ferrite according to the Schaeffler equations and diagram. Based on the observations, both filler metals accompanied by Ar-2%O2 shielding gas ...

متن کامل

منابع من

با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید


عنوان ژورنال:
international journal of iron & steel society of iran

ناشر: iron & steel society of iran

ISSN 1735-4145

دوره 10

شماره 1 2013

میزبانی شده توسط پلتفرم ابری doprax.com

copyright © 2015-2023