Polycarbonate as an Elasto-Plastic Material Model for Simulation of the Microstructure Hot Imprint Process

نویسندگان

  • Birute Narijauskaite
  • Arvydas Palevicius
  • Rimvydas Gaidys
  • Giedrius Janusas
  • Rokas Sakalys
چکیده

The thermal imprint process of polymer micro-patterning is widely applied in areas such as manufacturing of optical parts, solar energy, bio-mechanical devices and chemical chips. Polycarbonate (PC), as an amorphous polymer, is often used in thermoforming processes because of its good replication characteristics. In order to obtain replicas of the best quality, the imprint parameters (e.g., pressure, temperature, time, etc.) must be determined. Therefore finite element model of the hot imprint process of lamellar periodical microstructure into PC has been created using COMSOL Multiphysics. The mathematical model of the hot imprint process includes three steps: heating, imprinting and demolding. The material properties of amorphous PC strongly depend on the imprint temperature and loading pressure. Polycarbonate was modelled as an elasto-plastic material, since it was analyzed below the glass transition temperature. The hot imprint model was solved using the heat transfer and the solid stress-strain application modes with thermal contact problem between the mold and polycarbonate. It was used for the evaluation of temperature and stress distributions in the polycarbonate during the hot imprint process. The quality of the replica, by means of lands filling ratio, was determined as well.

برای دانلود رایگان متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

FE-Based Analysis of Hot Forming Process Using the Flow Stress Prediction Model

In hot forming process, the workpiece undergoes plastic deformation at high temperature and the microstructure of the workpiece changes according to the plastic deformation. These changes affect the mechanical properties of workpiece. In order to optimize this process, both the plastic deformation of workpiece and its microstructural changes should be taken into consideration. Since material be...

متن کامل

FE-Based Analysis of Hot Forming Process Using the Flow Stress Prediction Model

In hot forming process, the workpiece undergoes plastic deformation at high temperature and the microstructure of the workpiece changes according to the plastic deformation. These changes affect the mechanical properties of workpiece. In order to optimize this process, both the plastic deformation of workpiece and its microstructural changes should be taken into consideration. Since material be...

متن کامل

Elasto-plastic solution for thick-walled spherical vessels with an inner FGM layer

Purely elastic, partially and fully plastic stress states in a thick-walled spherical pressure vessel with an inner functionally graded material (FG) coating subjected to internal and external pressures are developed analytically in this paper. The modulus of elasticity and the uniaxial yield limit of the FG coating layer are considered to vary nonlinearly through the thickness. Using Tresca’s ...

متن کامل

A 3D elasto-plastic FEM program developed for reservoir Geomechanics simulations: Introduction and case studies

The development of yielded or failure zone due to an engineering construction is a subject of study in different disciplines. In Petroleum engineering, depletion from and injection of gas into a porous rock can cause development of a yield zone around the reservoir. Studying this phenomenon requires elasto-plastic analysis of geomaterial, in this case the porous rocks. In this study, which is a...

متن کامل

A FEM Multiscale Homogenization Procedure using Nanoindentation for High Performance Concrete

This paper aims to develop a numerical multiscale homogenization method for prediction of elasto-viscoplastic properties of a high performance concrete (HPC). The homogenization procedure is separated into two-levels according to the microstructure of the HPC: the mortar or matrix level and the concrete level. The elasto-viscoplastic behavior of individual microstructural phases of the matrix a...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

عنوان ژورنال:

دوره 13  شماره 

صفحات  -

تاریخ انتشار 2013