Study of two cohorts of workers exposed to methyl methacrylate in acrylic sheet production.

نویسندگان

  • J A Tomenson
  • S M Bonner
  • J C Edwards
  • M A Pemberton
  • T F Cummings
  • G M Paddle
چکیده

OBJECTIVES To study mortality among 4324 workers at two United Kingdom factories, Darwen, Lancashire and Wilton, Cleveland, producing polymethyl methacrylate (PMMA) sheet. The Darwen factory is still active, but the Wilton one was closed in 1970. Also, to investigate patterns of mortality after exposure to methyl methacrylate; in particular, mortality from colon and rectal cancer. METHODS All male employees at the Darwen factory with a record of employment in 1949-88 and all men ever employed at the Wilton factory (1949-70) were investigated. The vital status of both cohorts was ascertained on 31 December 1995. The exposure of 1526 subjects at the Darwen plant who were engaged from 1949 onwards could be characterised. The mean duration of exposure was 7.6 years at 13.2 ppm (8 hour time weighted average), although exposures in some work groups were as high as 100 ppm. It was not possible to calculate the cumulative exposure of workers first employed at the Darwen plant before 1949 or workers at the Wilton factory. RESULTS In the Darwen cohort, 622 deaths were identified and a further 700 deaths in the Wilton cohort. Mortalities for the cohort were compared with national and local rates and expressed as standardised mortality ratios (SMRs). In the subcohort of Darwen workers with more than minimal exposure to MMA, reduced mortalities compared with national and local rates, were found for all causes (SMR 94), and colorectal cancer (SMR 92), but mortality from all cancers was slightly increased (SMR 104). No relations were found with cumulative exposure to MMA. In the subcohort of Wilton workers, mortality from all causes of death was significantly reduced (SMR 89), but mortality from all cancers (SMR 103) and colorectal cancer (SMR 124) were increased. The excess of colorectal cancer was confined to employees with less than 1 year of employment. CONCLUSION The study provided no clear evidence that employment at the factories or exposure to MMA had adversely affected the mortalities of workers.

برای دانلود رایگان متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

The Release of Residual Monomeric Methyl Methacrylate in Human Saliva after Using Acrylic Dentures

The Release of Residual Monomeric Methyl Methacrylate in Human Saliva after Using Acrylic Dentures Dr. AH. Alehavaz* - Dr. D. Qujeq** - Dr. A. Babapour*** *- Assistant Professor of Prosthodontics Dept. – Faculty of Dentistry – Babol University of Medical Sciences. **- Associate Professor of Biochemistry and Biophysics Dept. – Babol University of Medical Sciences. ***- Dentist. Background and Ai...

متن کامل

The effect of SiO2 nano-filler addition into heat-cured poly methyl methacrylate on three-point flexural strength

Background and Aims: Poly methyl methacrylate (PMMA) is still the most commonly used material in prosthetic dentistry. However, there are problems with the mechanical properties of this type of material including low flexural strength. Addition of nanoparticles into the polymer is one way to improve the mechanical properties of acrylic resin. In the present study, the effect of silicon dioxide ...

متن کامل

Design and Production of Two-Piece Thyroid-Neck Phantom by the Concurrent Use of Epoxy Resin and Poly(Methyl Methacrylate) Soft Tissue Equivalent Materials

The aim of this report is to present a new two-piece thyroid-neck phantom produced by the concurrent use of epoxy resin and poly(methyl methacrylate) (PMMA: plexiglass) soft tissue equivalent materials. Accordingly, mass attenuation coefficients of the epoxy resin and the plexiglass compounds were obtained from simulation (NIST XCOM 3.1) and measurements (practical dosimetry) and compared to th...

متن کامل

Mini-emulsion preparation, kinetics of reaction and physical properties of acrylic terpolymer lattices

In this study, stable lattices of terpolymer butyl acrylate, methyl methacrylate, and styrene were synthesized by a mini-emulsion polymerization technique using tert-butyl hydroperoxide TBHP/Fe2 /ethylenediaminetetraacetic acid/sodium formaldehyde sulfoxylate redox initiators at room temperature, and the kinetics of the reaction were studied. The reaction rate was obtained from periodic samplin...

متن کامل

Comparison of Water Sorption of Two Injection Acrylic Resins with a Conventional Pressure-Packed Acrylic Resin

Background and Aim: Water sorption is one of the most important properties that affects the quality of a prosthesis, and subsequently, the quality of treatment, and pa-tient’s quality of life. The aim of this study was to determine and compare the water sorption of two types of poly methyl methacrylate (PMMA) using the injection-molding systems with a traditional acrylic resin base material. M...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

عنوان ژورنال:
  • Occupational and environmental medicine

دوره 57 12  شماره 

صفحات  -

تاریخ انتشار 2000