Automatic Design Centering of Analog Integrated Circuits Based on the Generalized Boundary Curve of Multiple Robustness Objectives

نویسنده

  • Robert Schwencker
چکیده

In this report a method for the design centering of analog circuits, based on worstcase distances (WCD) is presented. In order to keep the linearization error small, only the WCDs and not the strongly nonlinear objective function itself is linearized. For the resulting nonlinear trust-region problem the generalized boundary curve (GBC) is derived as a method to determine a solution with a good ratio between error reduction and norm of the parameter correction. This parameter correction is used in a standard iterative trust-region optimization algorithm. Results calculated on a circuit example show a signifcant reduction of iterations compared to a standard gradient-based optimization algorithm. Thus, design centering becomes applicable within industrial analog circuit design.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

MOCA ARM: Analog Reliability Measurement based on Monte Carlo Analysis

Due to the expected increase of defects in circuits based on deep submicron technologies, reliability has become an important design criterion. Although different approaches have been developed to estimate reliability in digital circuits and some measuring concepts have been separately presented to reveal the quality of analog circuit reliability in the literature, there is a gap to estimate re...

متن کامل

Time-Mode Signal Quantization for Use in Sigma-Delta Modulators

The rapid scaling in modern CMOS technology has motivated the researchers to design new analog-to-digital converter (ADC) architectures that can properly work in lower supply voltage. An exchanging the data quantization procedure from the amplitude to the time domain, can be a promising alternative well adapt with the technology scaling. This paper is going to review the recent development in t...

متن کامل

Preferred Robust Response Surface Design with Missing Observations Based on Integrated TOPSIS-AHP Method

- Missing observations occur in experimental designs as a result of insufficient sampling, machine breakdown, high cost, and errors in the measurements. In nanomanufacturing, missing observations often appear in designs because the combination of factors or molecular structures selected by a designer cannot be experimented successfully. In the current paper, Box-Behnken and face-centered compos...

متن کامل

1 Analog Circuit Design based on Robust POFs using an Enhanced MOEA with SVM Models

In this chapter, a multi-objective design methodology for automatic analog integrated circuits (IC) synthesis, which enhances the robustness of the solution by varying technological and environmental parameters, is presented. The automatic analog IC sizing tool GENOM-POF was implemented and used to demonstrate the methodology, and to verify the effect of corner cases on the Pareto optimal front...

متن کامل

Design and Implementation of MOSFET Circuits and CNTFET, Ternary Multiplier in the Field of Galois

Due to the high density and the low consumption power in the digital integrated circuits, mostly technology of CMOS is used. During the past times, the Metal oxide silicon field effect transistors (MOSFET) had been used for the design and implementation of the digital integrated circuits because they are compact and also they have the less consumption power and delay to the other transistors. B...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 1999