Optimization on Delamination of Cutting Parameter during Drilling on Gfrp Plastics Based on Taguchi Method

نویسندگان

  • P. P. PATIL
  • N. B. GURULE
چکیده

Drilling of glass fibre reinforced plastic (GFRP) composite is different from metallic materials due to its mechanical properties. The drilling of this material may generate delamination of drilled holes on workpiece. The purpose of this paper is to investigate the influence of the cutting parameters, such as cutting speed and feed rate, point angle of drill and material thickness on delamination produced when drilling a GFRP composite. The damage generated associated with drilling GFRP composites were observed, both at the entrance and the exit during the drilling. Hence it is essential to obtain optimum cutting parameters minimizing delamination at drilling of GFRP composites. This paper presents the application of Taguchi method for minimization of delamination influenced by drilling parameters and drill point angle and material thickness. The optimum drilling parameter combination was obtained by using the analysis of signal-to-noise ratio. The conclusion revealed that the feed rate, cutting speed, point angle and thickness are the most influential factor on the delamination, respectively.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Determination of optimum parameters on delamination in drilling of GFRP composites by Taguchi method

Drilling is one of the important machining processes in hole making operations. Delamination is a vital problem during any drilling operation. It causes structural integrity reduction and poor assembly tolerance as well as potential for long-term performance deterioration. As a result, drilling of any material requires dimensional stability and interface quality. In this study, glass fibre rein...

متن کامل

Optimization of Process Parameters in Drilling of GFRP Composites Drilled by an End Mill

Abstract— Due to the superior physical and mechanical properties Glass fiber-reinforced (GFRP) composite materials are very attractive for applications like aerospace and air craft structural components. This results a large number of research papers on machining of these composite laminates. Out of all the machining operations, most commonly used operation is drilling. However, drilling operat...

متن کامل

Drilling Of Tio2 and Zns Filled Gfrp Composites: A Taguchi Approach

The main affecting parameter for Delamination of the composites and in turn the failure of composites is the Thrust force. In the present work an attempt has been made in order to investigate the Thrust force generated during drilling of the TiO2 and ZnS filled Glass Fabric Reinforced Polymer Matrix Composites (GFRP). The volume fractions in the matrix were chosen as 1, 2 and3%. A plan of exper...

متن کامل

Optimization of Drilling Parameters on Delamination Based on Taguchi Method in Drilling of Natural Fiber Reinforced (Agave) Composite

Agave is the one of the abundantly available plant in India. The wide application of agave reinforced composite plate necessitate the joining of two plates together. For making such joint drilling of those plates is required. Drilling of natural fiber composites is different from the other metals because of its mechanical properties. The major problem faced in drilling of theses natural fiber c...

متن کامل

Predicting Drilling Forces and Delamination in GFRP Laminates using Fuzzy Logic

Drilling of fiber reinforced plastics is necessary in order to assemble complex/intricate composite products. Drilling induced damage leads to high percentage of part rejection and reduced product efficiency and life. The thrust force and torque have been found to be the important factors influencing damage. In the present research endeavor, an attempt has been made to develop a fuzzy rule base...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2013