Eigenvalue method for computing size effect of cohesive cracks with residual stress, with application to kink-bands in composites

نویسنده

  • Goangseup Zi
چکیده

The previously developed eigenvalue method for computing the size effect of cohesive crack model is extended to the cohesive crack model with a finite residual stress. In this model, the structure size for which a specified relative length of kink-band corresponds to the maximum load is obtained as an eigenvalue of a homogeneous Fredholm integral equation. This new method is direct and much more efficient than the classical finite element approach in which the entire load-deflection history must be computed to obtain the maximum load. A secondary purpose of the paper is to apply the new method to the effect of structure size on the compressive strength of unidirectional fiber–polymer composites failing by propagation of kinkband with fiber microbuckling. The kink-band is simulated by a cohesive crack model with a linear compressive softening law and a finite residual stress. The simulation shows that the specimens tested have a negative–positive geometry, i.e., the energy release rate of the kink-band for a unit load first decreases but at a certain length of propagation begins to increase. Finally the effect of shape of the softening law of cohesive crack on the size effect curve is studied by using the new eigenvalue method. It is shown that, for a negative–positive geometry, the size effect on the peak load depends on the entire softening curve if the specimens is not too small. 2003 Elsevier Science Ltd. All rights reserved.

برای دانلود رایگان متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Application of Pulse Method to Incremental Slitting Measurement of Residual Stresses in Laminated Composites

In this research, the incremental slitting method was employed to determine throughthickness residual stress profile of a carbon/epoxy laminate. The method involves measuring strains at the back surface of the stressed specimen, while a narrow slit is cut by a CNC milling machine progressively from the top surface of the specimen. "Pulse Method" was selected as the computational approach for th...

متن کامل

Investigation of Important Parameters in Residual Stress Determination in Isotropic Plates and Laminated Composites by Slitting Method

In the slitting method, a small width slit is created incrementally through the thickness of the stressed specimen and the released strains in each increment are recorded by a strain gauge. Compliance coefficients relate the measured strains to the residual stresses. This paper investigates the important parameters influencing the calculation of compliance coefficients for isotropic plates and ...

متن کامل

Inelastic strain distribution and seismic radiation from rupture of a fault kink

[1] We extend an elastodynamic finite element method to incorporate off-fault plastic yielding into a dynamic earthquake rupture model. We simulate rupture for models of faults with a kink (a sharp change in fault strike), examining how off-fault plastic yielding affects rupture propagation, seismic radiation, and near-fault strain distribution. We find that high-frequency radiation from a kink...

متن کامل

Mixed-Mode Stress Intensity Factors for Surface Cracks in Functionally Graded Materials Using Enriched Finite Elements

Three-dimensional enriched finite elements are used to compute mixed-mode stress intensity factors (SIFs) for three-dimensional cracks in elastic functionally graded materials (FGMs) that are subject to general mixed-mode loading. The method, which advantageously does not require special mesh configuration/modifications and post-processing of finite element results, is an enhancement of previou...

متن کامل

Measurement of Variation in Fracture Strength and Calculation of Stress Concentration Factor in Composite Laminates with Circular Hole

In this research, residual strength and stress concentration factor of laminated composites with a circular open hole are studied analytically, numerically and experimentally. The numerical study was carried out using the finite element method. Moreover an analytical study was carried out with developing of point stress criterion. Mechanical testing was performed to determine the un-notched ten...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2003