Space Advantage Provided by De - Laval Nozzle and Bell Nozzle over Venturi

نویسنده

  • Omkar N. Deshpande
چکیده

Abstract:-The FSAE guidelines state that it is mandatory for each and every car participating in the said event to have a single circular 20mm restrictor in the intake system. All the air flowing to the engine must pass through this restrictor. Conventionally, a Venturi Nozzle is used as a restrictor. In our research, we have proposed two Nozzles: De-Laval Nozzle and Bell Nozzle as an alternative to the Venturi Nozzle. After numerous CFD Simulations; we have inferred that the results of the De-Laval Nozzle and Bell Nozzle are similar to the Venturi Nozzle. Along with providing similar results, the two nozzles provide a space saving of 6.86% over the Venturi Nozzle. The data was gathered from SolidWorks Flow Simulation 2014.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

A Theoretical Mass Transfer Approach for Prediction of Droplets Growth Inside Supersonic Laval Nozzle

Proper estimation of droplet growth rate plays a crucial role on appropriate prediction of supersonic separators performance for separation of fine droplets from a gas stream. Up to now, all available researches employ empirical or semi-empirical correlations to define the relationship between droplet growth rate (dr/dt) and other operating variables such as temperatures (T and TL), Pressure (P...

متن کامل

Transonic Potential Flows in A Convergent–Divergent Approximate Nozzle

In this paper we prove existence, uniqueness and regularity of certain perturbed (subsonic–supersonic) transonic potential flows in a two-dimensional Riemannian manifold with “convergent–divergent” metric, which is an approximate model of the de Laval nozzle in aerodynamics. The result indicates that transonic flows obtained by quasi-one-dimensional flow model in fluid dynamics are stable with ...

متن کامل

Simulation of Cold Spray Nozzle Accompanying a Water-cooling Adjustment

Cold spraying is a coating process which enables production of metallic and metallic ceramic coatings with dense (very low porosity level) and pure (low oxygen content) structures. Several coating applications such as corrosion resistance and electrical conductivity rely on these properties. Generally, cold spraying is based on higher particle velocities and lower process temperatures than othe...

متن کامل

Experimental Study on Performance of Two-phase Ejector Refrigeration Cycle System with Two-throat Nozzle

The two-phase ejector refrigeration cycle (TPERC) system with a two-throat nozzle ejector was investigated experimentally, and the entrainment ratio of the ejector and the COP of the system were compared with those of the ejector with Laval nozzle and its TPERC system respectively. The experimental results indicate that under the working condition of the evaporating/condensing temperatures 1°C/...

متن کامل

Compressible Euler Flows on a Convergent–Divergent Surface: Steady Subsonic Flows

In this paper, we construct various special solutions on a convergent-divergent surface for the steady compressible complete Euler system and established the stability of the purely subsonic flows. For a given pressure p0 prescribed at the “entry” of the surface, as the pressure p1 at the “exit” decreases, the flow patterns on the surface change continuously as those happen in a de Laval nozzle...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2015