Characterization of Open Cell Sic Foam Material
نویسندگان
چکیده
This paper presents characterization and modeling of microwave characteristics of SiC foam material. Transmission and reflection measurements are performed in X, K and Ka band for the samples of two different pore sizes and three different thicknesses. Effective and frequency dependent dielectric permittivity is extracted for 50PPI 10mm sample, while for the other samples it was not possible because of density gradient in the samples. By calculation of Mie scattering efficiencies approximate magnitude of dominant loss mechanism (scattering or absorption) at certain frequencies is predicted.
منابع مشابه
Investigation of Glass- Steel Slag Foam Composite Sintering in Presence of SiC
Amorphous steel slag was blended with different concentrations of waste glass (20, 40, 50, 60, 70 wt.%) and SiC to obtain a composite. According to Hot Stage Microscopy images, slag-glass composite contractions started at 1050 ºC. scanning electron microscope micrographs of slag-SiC (foaming agent) composite revealed tunnel-like porosities of 500 to 1000 microns. Gaseous products of carbide dec...
متن کاملNumerical predictions for radar absorbing silicon carbide foams using a finite integration technique with a perfect boundary approximation
Modeling and prediction of electromagnetic wave absorbing properties of SiC foams as novel stealth materials in the X-band range of 8.2–12.4 GHz are presented. Appropriate material parameters, including the conductivity, volume fraction, cell size, thickness, and surface modified foam structure, are determined through optimization calculations, where the impedance difference between the SiC foa...
متن کاملبررسی عوامل حباب‌زای TiH2و CaCO3 بر ساختار وخواص کامپوزیت فومی Al-7%Si-3%SiC
In this paper, the effect of TiH2 and CaCO3 blowing agents was investigated on the structure and energy absorption of Al-7%Si-3%SiC composite metal foam by powder compact route. Composition of the foam was prepared from a mixture of Al, SiC and Si powders. Then, precursors were consolidated in H13 die mould by cold and uni-axial pressing at 110 MPa and at room temperature. The pressed precursor...
متن کاملاثر ساختار سلولی فوم آلومینیم کامپوزیتی A356-10vol.%SiCبر رفتار شبه استاتیکی کمانش پلاستیک پیشرونده قوطی‌های برنجی پرشده با آن
In this paper, the behavior of energy absorption of crush-boxes, made of Aluminum foam advanced material, was investigated based on foam cellular structure homogeneity. Therefore, thin-walled tubes of Cu-Zn30wt.%.brass alloy with 27 mm diameter and 1 mm thickness were filled with A356-10vol.%SiC-Xwt.%. of TiH2 foam liquid. Foam samples with 1, 1.5, 2wt.%. of TiH2 were prepared by Form Grip into...
متن کاملDevelopment of Clay Foam Ceramic as a Support for Fungi Immobilization to Biodiesel Production (RESEARCH NOTE)
Biodiesel is an attractive alternative fuel because of its nontoxicity and biodegradability properties. Biodiesel is produced through transesterification of vegetable oils’ triglyceride. It is obtained from vegetable oils or fats either by chemical or enzyme-catalyzed transesterification with methanol or ethanol. By using whole-cell biocatalyst immobilized within biomass support particles (BSPs...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
عنوان ژورنال:
دوره شماره
صفحات -
تاریخ انتشار 2012