Intermittent ‘self-locking’ of Grain Growth in Fine-grained Materials

نویسندگان

  • Y. Estrin
  • G. Gottstein
چکیده

Grain boundary motion may be accompanied with vacancy generation [1–4]. A typical case where a moving grain boundary produces vacancies is in primary recrystallisation, when the growth of a recrystallised grain at the cost of a grain with a large dislocation density involves release of excess free volume. Vacancies are also generated during grain growth, when the total volume of the grain boundary ‘phase’, which is less dense than the bulk, decreases, again leading to release of excess free volume. Interaction of moving grain boundaries with the vacancy atmospheres generated by themselves was shown to affect the grain boundary kinetics [2–4]. The effects are akin to impurity drag of grain boundaries. A kinetic approach taken in Refs. 2–4 made it possible to consider individual grain boundary motion. In the present communication, we look at the vacancy drag of grain boundaries during grain growth in a holistic way. Using a simple thermodynamic argument we shall determine conditions under which grain growth can be ‘suffocated’ by the concomitant vacancy generation. A simple criterion for ‘self-locking’ of grain growth will be presented. On this basis, a picture of intermittent grain growth is proposed in which stages of grain boundary motion are separated by periods of arrest. It is suggested that grain growth induced vacancy generation may be considered as a stabilising effect inhibiting grain growth in fine grained materials. The effect discussed is of particular significance for ultrafine grained polycrystals, notably nanocrystalline materials.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Superplasticity of a fine-grained Mg–1.5 wt% Gd alloy after severe plastic deformation

The strain rate sensitivity (SRS) of Mg–1.5 wt% Gd processed by conventional extrusion and 2 passes of simple shear extrusion (SSE) was investigated by shear punch testing. Shear punch tests were conducted at initial shear strain rates in the range of 0.003–0.3 s-1 and at temperatures in the range of 573–773 K. A fine-grained microstructure with an average grain size of about 2.5 µm, obtained a...

متن کامل

Pii: S1359-6454(99)00235-9

ÐThe inhibiting e€ect of vacancies on the very process in which they are generated is considered from a thermodynamic viewpoint. Examples of such processes treated here in some detail are grain growth and pore dissolution. It is shown that these processes are inhibited due to vacancy generation. A particular scenario discussed implies intermittent ``locking''. After a period of uninhibited kine...

متن کامل

Grain Refinement of Dual Phase Steel via Tempering of Cold-Rolled Martensite

A microstructure consisting of ultrafine grained (UFG) ferrite with average grain size of ~ 0.7 µm and dispersed nano-sized carbides was produced by cold-rolling and tempering of the martensite starting microstructure in a low carbon steel. Subsequently, fine grained dual phase (DP) steel consisting of equiaxed ferrite grains with average size of ~ 5 µm and martensite islands with average size ...

متن کامل

A study on the sub-structure and mechanical properties of friction stir processed AA 6061-T6 joints with ultra-fine grained structure

Ultra-fine grained (UFG) structure (~0.6 µm) was produced in the stir zone (SZ) of 6061-T6 aluminum alloy joints using friction stir processing (FSP) cooled by liquid nitrogen (N2). A new experimental set-up was used to simultaneously quench the lower and upper surfaces of the samples during the processing. In addition, FSPed joints, using a steel backing plate, were produced at room temperatur...

متن کامل

Ultra-Fine Grained Dual-Phase Steels

This paper provides an overview on obtaining low-carbon ultra-fine grained dual-phase steels through rapid intercritical annealing of cold-rolled sheet as improved materials for automotive applications. A laboratory processing route was designed that involves cold-rolling of a tempered martensite structure followed by a second tempering step to produce a fine grained aggregate of ferrite and ca...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 1999