Rational design of modular circuits for gene transcription: A test of the bottom-up approach

نویسندگان

  • Francesca Ceroni
  • Simone Furini
  • Emanuele Giordano
  • Silvio Cavalcanti
چکیده

BACKGROUND Most of synthetic circuits developed so far have been designed by an ad hoc approach, using a small number of components (i.e. LacI, TetR) and a trial and error strategy. We are at the point where an increasing number of modular, inter-changeable and well-characterized components is needed to expand the construction of synthetic devices and to allow a rational approach to the design. RESULTS We used interchangeable modular biological parts to create a set of novel synthetic devices for controlling gene transcription, and we developed a mathematical model of the modular circuits. Model parameters were identified by experimental measurements from a subset of modular combinations. The model revealed an unexpected feature of the lactose repressor system, i.e. a residual binding affinity for the operator site by induced lactose repressor molecules. Once this residual affinity was taken into account, the model properly reproduced the experimental data from the training set. The parameters identified in the training set allowed the prediction of the behavior of networks not included in the identification procedure. CONCLUSIONS This study provides new quantitative evidences that the use of independent and well-characterized biological parts and mathematical modeling, what is called a bottom-up approach to the construction of gene networks, can allow the design of new and different devices re-using the same modular parts.

برای دانلود رایگان متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Modular approach for an ASIC integration of electrical drive controls

VLSI circuits design allows today to consider new modes of implementation for electrical controls. However, design techniques require an adaptation effort that few designers, too accustomed to the software approach, provide. The authors of this article propose to develop a methodology to guide the electrical designers towards optimal performances of control algorithms implementation. Thus, they...

متن کامل

Rapid SARS-CoV-2 RT-LAMP assay setup using gene construct design approach

Background and Objective: The severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) is still an ongoing challenge in health system worldwide. Molecular detection methods including reverse transcription loop-mediated isothermal amplification (RT-LAMP) can help cutting off the transmission chain of the virus. In this study, prompt setting up of the RT-LAMP assays were investigated using ge...

متن کامل

Comparing the effectiveness of pharmacotherapy (paroxetine), modular cognitive-‎ behavioral therapy ‎‌‌and their combination in distress tolerance, ambiguity tolerance and meta-worry‎ in female university students with generalized anxiety disorder

Introduction In the last two decades, the interest in understanding the nature of generalized anxiety disorder (GAD) and the development of effective treatment methods for GAD has increased among psychologists. This study aimed to compare the effectiveness of pharmacotherapy, modular cognitive-‎behavioral therapy ‎‏‏and their combination in distress tolerance, ambiguity tolerance and meta-worr...

متن کامل

A Design Methodology for Reliable MRF-Based Logic Gates

Probabilistic-based methods have been used for designing noise tolerant circuits recently. In these methods, however, there is not any reliability mechanism that is essential for nanometer digital VLSI circuits. In this paper, we propose a novel method for designing reliable probabilistic-based logic gates. The advantage of the proposed method in comparison with previous probabilistic-based met...

متن کامل

EFFICIENT SIMULATION FOR OPTIMIZATION OF TOPOLOGY, SHAPE AND SIZE OF MODULAR TRUSS STRUCTURES

The prevalent strategy in the topology optimization phase is to select a subset of members existing in an excessively connected truss, called Ground Structure, such that the overall weight or cost is minimized. Although finding a good topology significantly reduces the overall cost, excessive growth of the size of topology space combined with existence of varied types of design variables challe...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

عنوان ژورنال:

دوره 4  شماره 

صفحات  -

تاریخ انتشار 2010