In situ spectroscopic study of the plastic deformation of amorphous silicon under non-hydrostatic conditions induced by indentation.

نویسندگان

  • Y B Gerbig
  • C A Michaels
  • J E Bradby
  • B Haberl
  • R F Cook
چکیده

Indentation-induced plastic deformation of amorphous silicon (a-Si) thin films was studied by in situ Raman imaging of the deformed contact region of an indented sample, employing a Raman spectroscopy-enhanced instrumented indentation technique. Quantitative analyses of the generated in situ Raman maps provide unique, new insight into the phase behavior of as-implanted a-Si. In particular, the occurrence and evolving spatial distribution of changes in the a-Si structure caused by processes, such as polyamorphization and crystallization, induced by indentation loading were measured. The experimental results are linked with previously published work on the plastic deformation of a-Si under hydrostatic compression and shear deformation to establish a sequence for the development of deformation of a-Si under indentation loading. The sequence involves three distinct deformation mechanisms of a-Si: (1) reversible deformation, (2) increase in coordination defects (onset of plastic deformation), and (3) phase transformation. Estimated conditions for the occurrence of these mechanisms are given with respect to relevant intrinsic and extrinsic parameters, such as indentation stress, volumetric strain, and bond angle distribution (a measure for the structural order of the amorphous network). The induced volumetric strains are accommodated solely by reversible deformation of the tetrahedral network when exposed to small indentation stresses. At greater indentation stresses, the increased volumetric strains in the tetrahedral network lead to the formation of predominately five-fold coordination defects, which seems to mark the onset of irreversible or plastic deformation of the a-Si thin film. Further increase in the indentation stress appears to initiate the formation of six-fold coordinated atomic arrangements. These six-fold coordinated arrangements may maintain their amorphous tetrahedral structure with a high density of coordination defects or nucleate as a new crystalline β-tin phase within the a-Si network.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Phase transformations induced by spherical indentation in ion-implanted amorphous silicon

The deformation behavior of ion-implanted unrelaxed and annealed ion-implanted relaxed amorphous silicon a-Si under spherical indentation at room temperature has been investigated. It has been found that the mode of deformation depends critically on both the preparation of the amorphous film and the scale of the mechanical deformation. Ex situ measurements, such as Raman microspectroscopy and c...

متن کامل

Towards a deeper understanding of plastic deformation in mono-crystalline silicon

This paper investigates the plastic deformation in mono-crystalline silicon under complex loading conditions. With the aid of various characterization techniques, it was found that the mechanism of plasticity in silicon is complex and depends on loading conditions, involving dislocations, phase transformations and chemical reactions. In general, plastic deformation in silicon is the coupled res...

متن کامل

In situ TEM study of deformation-induced crystalline-to-amorphous transition in silicon

The mechanism responsible for deformation-induced crystalline-to-amorphous transition (CAT) in silicon is still under considerable debate, owing to the absence of direct experimental evidence. Here we have devised a novel core/shell configuration to impose confinement on the sample to circumvent early cracking during uniaxial compression of submicron-sized Si pillars. This has enabled large pla...

متن کامل

Finite element analysis of elastic-plastic solids under Vickers indentation: surface deformation

Finite element modeling has been used to study the development of surface deformation during indentation with a Vickers indenter. A wide range of materials with different elastic modulus and yield stresses are examined. Results show that in a pyramidal indentation process, for a perfectly plastic material, sinking-in during loading can change to pile-up in unloading. This phenomenon depends on ...

متن کامل

Experimental and Finite Element Analyses of the Hydrostatic Cyclic Expansion Extrusion (HCEE) Process with Back-Pressure

It is generally known that severe plastic deformation processes with back pressure not only apply higher hydrostatic stress and more deformation compared to what a regular process can apply to a workpiece but also prevent surface defects in the workpiece during the process. Hydrostatic cyclic expansion extrusion (HCEE) was developed recently for processing long ultrafine-grained metals and allo...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • Physical review. B, Condensed matter and materials physics

دوره 92 21  شماره 

صفحات  -

تاریخ انتشار 2015