Refining experimental dental implant testing in the Göttingen Minipig using 3D computed tomography—A morphometric study of the mandibular canal
نویسندگان
چکیده
This study reports morphometric and age-related data of the mandibular canal and the alveolar ridge of the Göttingen Minipig to avoid complications during in vivo testing of endosseus dental implants and to compare these data with the human anatomy. Using 3D computed tomography, six parameters of the mandibular canal as well as the alveolar bone height and the alveolar ridge width were measured in Göttingen Minipigs aged 12, 17 and 21 months. Our null hypothesis assumes that the age and the body mass have an influence on the parameters measured. The study found that the volume, length and depth of the mandibular canal all increase with age. The width of the canal does not change significantly with age. The body mass does not have an influence on any of the measured parameters. The increase in canal volume appears to be due to loss of deep spongy bone in the posterior premolar and molar regions. This reduces the available space for dental implantations, negatively affecting implant stability and potentially the integrity of the inferior alveolar neurovascular bundle. Dynamic anatomical changes occur until 21 months. On ethical grounds, using minipigs younger than 21 months in experimental implant dentistry is inadvisable. Paradoxically the measurements of the 12 months old pigs indicate a closer alignment of their mandibular anatomy to that of humans suggesting that they may be better models for implant studies. Given the variability in mandibular canal dimensions in similar age cohorts, the use of imaging techniques is essential for the selection of individual minipigs for dental prosthetic interventions and thus higher success rates.
منابع مشابه
Evaluation of mandibular premolars root canal morphology by cone beam computed tomography
Introduction: To achieve a successful endodontic treatment, the clinician has to identify the different canal configurations.mandibular premolars have the wide variety of root canal morphology and they are known as the most difficult teeth to treat in endodontics.CBCT provides a non-invasive 3D confirmatory diagnosis as a complement to conventional radiography.The aim of this study was to...
متن کاملAssessment of the inferior mandibular canal’s position by Cone-Beam Computed Tomography
Abstract Objectives: It is important to know the exact location and anatomic variety of inferior alveolar nerve canal for different procedures of mandibular surgeries. The aim of the present study was to evaluate inferior mandibular canal’s anatomic position by Cone-beam Computed Tomography (CBCT). Methods: In a cross sectional study, CBCT were taken and assessed from 130 patients (...
متن کاملInvestigating Root Canal Number and Morphology of Mandibular Anterior Teeth Using Cone Beam Computed Tomography
Background and purpose: Root therapy will be successful if it is done based on a correct diagnosis and appropriate treatment plan with the knowledge of morphology and tooth anatomy, debridement, disinfection, and obturation of the entire root canal system. This study aimed to investigate the number and morphology of canals in root canals mandibular anterior using cone beam computed tomography (...
متن کاملSpatial Relationship between Mandibular Third Molars and Inferior Alveolar Nerve using a Volume Rendering Software
Precise localization of the third molars in relation to the inferior alveolar nerve canal is critical from a clinical point of view and strongly affects the surgical treatment outcome. Recently, by using three-dimensional modeling software, the relationship of third molar root apices and inferior alveolar nerve canal can be better understood. In this study, the spatial relationship of two surgi...
متن کاملAssociation between the peri-implant bone structure and stress distribution around the mandibular canal: a three-dimensional finite element analysis.
The aim of this study was to elucidate the association between the bone structure at implant insertion sites and stress distribution around the mandibular canal by means of three-dimensional finite element (3D FE) analysis. Four FE models were created with slice data using micro-computed tomography (micro-CT), and 3D FE analysis was performed. Mechanical analysis showed that the load reached th...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
عنوان ژورنال:
دوره 12 شماره
صفحات -
تاریخ انتشار 2017