Analysis of Voltage Variation in Silicon Carbide MOSFETs during Turn-On and Turn-Off

نویسندگان

  • Hui Li
  • Xinglin Liao
  • Yaogang Hu
  • Zhangjian Huang
  • Kun Wang
چکیده

Due to our limited knowledge about silicon carbide metal–oxide–semiconductor fieldeffect transistors (SiC MOSFETs), the theoretical analysis and change regularity in terms of the effects of temperature on their switching characteristics have not been fully characterized and understood. An analysis of variation in voltage (dVDS/dt) for SiC MOSFET during turn-on and turn-off has been performed theoretically and experimentally in this paper. Turn-off variation in voltage is not a strong function of temperature, whereas the turn-on variation in voltage has a monotonic relationship with temperature. The temperature dependence is a result of the competing effects between the positive temperature coefficient of the intrinsic carrier concentration and the negative temperature coefficient of the effective mobility of the electrons in SiC MOSFETs. The relationship between variation in voltage and supply voltage, load current, and gate resistance are also discussed. A temperature-based analytical model of dVDS/dt for SiC MOSFETs was derived in terms of internal parasitic capacitances during the charging and discharging processes at the voltage fall period during turn-on, and the rise period during turn-off. The calculation results were close to the experimental measurements. These results provide a potential junction temperature estimation approach for SiC MOSFETs. In SiC MOSFET-based practical applications, if the turn on dVDS/dt is sensed, the device temperature can be estimated from the relationship curve of turn on dVDS/dt versus temperature drawn in advance.

برای دانلود رایگان متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

A New Approach to High Efficincy in Isolated Boost Converters for High-Power Low- Voltage Fuel Cell Apllications

A new low-leakage-inductance low-resistance design approach to low-voltage high-power isolated boost converters is presented. Very low levels of parasitic circuit inductances are achieved by optimizing transformer design and circuit lay-out. Primary side voltage clamp circuits can be eliminated by the use of power MOSFETs fully rated for repetitive avalanche. Voltage rating of primary switches ...

متن کامل

TYPE N / A 3 . DATES COVERED - 4 . TITLE AND SUBTITLE 20 kV , 2 cm 2 , 4 H - SIC Gate Turn -

The need for high voltage solid-state power electronic devices for advanced power distribution and energy conversion has grown rapidly in recent years, especially for pulsed power applications that require high turn-on di/dt. However, current power converters built with silicon (Si) switches are quite bulky and inefficient, making their utilization difficult in practical energy conversion and p...

متن کامل

Operation and Performance of state-of-the-art High Temperature SiC Switches

This paper outlines recent developments in two dominant classes of Silicon Carbide based switches – the Super Junction Transistor (SJT) for 1.2kV-6.5kV pulse width modulated switching; and Thyristors for >6.5kV cycloconverter and pulsed power operation. The high-temperature (> 200 °C) blocking voltage, on-state and switching performance of recently fabricated 1200 V-class, 4H-SiC Super Junction...

متن کامل

Compact, Physics-Based Modeling of Nanoscale Limits of Double-Gate MOSFETs

Compact, physics-based models of subthreshold swing and threshold voltage are presented for double-gate (DG) MOSFETs in symmetric, asymmetric, and ground-plane modes. Applying these device models, threshold voltage variations in DG MOSFETs are comprehensively and exhaustively investigated using a unique, scale-length based methodology. Quantum mechanical effects and fringeinduced barrier loweri...

متن کامل

Effect of Particle Volume Fraction on the Tensile Properties of Composite Al6061/SiC Materials by Hot Extrusion

In the present study the effect of phase volume fraction on the reinforcement of microstructure and tensile properties of composite extrusion process Al6061/SiC has been studied. For this purpose, the base alloy Al6061 using pure aluminum ingots, silicon, of Al-50% Mg, Al-10% Cr and a thin copper rod was prepared. Next, the composite Al6061/5% SiC, Al6061/10% SiC, Al6061/15% SiC and Al6061/20% ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2017