Synthesis of p-Type Gallium Nitride Nanowires for Electronic and Photonic Nanodevices

نویسندگان

  • Zhaohui Zhong
  • Fang Qian
  • Deli Wang
  • Charles M. Lieber
چکیده

Magnesium-doped gallium nitride nanowires have been synthesized via metal-catalyzed chemical vapor deposition. Nanowires prepared on c-plane sapphire substrates were found to grow normal to the substrate, and transmission electron microscopy studies demonstrated that the nanowires had single-crystal structures with a 〈0001〉 growth axis that is consistent with substrate epitaxy. Individual magnesium-doped gallium nitride nanowires configured as field-effect transistors exhibited systematic variations in two-terminal resistance as a function of magnesium dopant incorporation, and gate-dependent conductance measurements demonstrated that optimally doped nanowires were p-type with hole mobilities of ca. 12 cm2/V‚s. In addition, transport studies of crossed gallium nitride nanowire structures assembled from pand n-type materials show that these junctions correspond to well-defined p−n diodes. In forward bias, the p−n crossed nanowire junctions also function as nanoscale UV-blue light emitting diodes. The new synthesis of p-type gallium nitride nanowire building blocks opens up significant potential for the assembly of nanoscale electronics and photonics. Semiconductor nanowires (NWs) have demonstrated significant potential as fundamental building blocks for nanoelectronic and nanophotonic devices and also offer substantial promise for integrated nanosystems.1,2 A key feature of semiconductor NWs that has enabled much of their success has been the growth of materials with reproducible electronic properties, including the controlled incorporation of n-type and/or p-type dopants.3-5 The ability to incorporate both pand n-type dopants in a single material system, called complementary doping, has been previously demonstrated in silicon (Si)3,4 and indium phosphide (InP)5 NWs and has opened up substantial opportunities for exploring nanodevice concepts. For example, p-type and n-type Si NWs have been used to assemble p-n diodes, bipolar transistors, and complementary inverters,3,4 while pand n-type InP NWs have been used to create p-n diodes that function as nanoscale near-infrared light-emitting diodes (LEDs).5 Complementary doping has not been reported in other semiconductor NW materials, although these previous results for Si and InP NWs underscore how the availability of pand n-type materials can enable a wide-range of function. For example, there has been considerable interest in GaN NWs6-8 since this wide band gap material has been used in conventional planar structures to fabricate UV-blue LEDs and lasers,9 as well as a range of other high-performance electronic devices.10 Studies of the electronic properties of GaN NWs show, however, that unintentionally doped materials are intrinsically n-type,11,12 and thus alone preclude exploration of a wide-range of nanodevices based upon complementary materials. To overcome this limitation of available GaN NWs, we have previously used p-Si NWs and n-GaN NWs to assemble hetero p-n junctions and nano-LEDs,11,13 although a limitation of using p-Si NWs in these nanostructures is that the band offsets yield a large asymmetry in the barriers for injection of holes and electrons at the junction. The synthesis of p-type GaN NWs could eliminate this issue and thus should impact further development of GaN NW-based electronics and photonics. Herein we report the first successful synthesis of p-type GaN (p-GaN) NWs, where magnesium is used as the p-type dopant,9 and the assembly and characterization of p-GaN single NW field-effect transistors (FETs), p-GaN/n-GaN crossed NW diodes, and UVblue p-GaN/n-GaN crossed NW nanoLEDs. GaN NWs were prepared via metal-catalyzed chemical vapor deposition (CVD), using ammonia (99.99%, Matheson), gallium metal (99.9999%, Alfa Aesar), and magnesium nitride (Mg3N2, 99.6%, Alfa Aesar) as the N, Ga, and Mg sources, respectively, and c-plane sapphire as the growth substrate. The Mg3N2 decomposes thermally as Mg3N2(s) ) * Corresponding author. † Department of Chemistry and Chemical Biology. ‡ Division of Engineering and Applied Sciences. § These authors contributed equally to this work. NANO LETTERS 2003 Vol. 3, No. 3 343-346 10.1021/nl034003w CCC: $25.00 © 2003 American Chemical Society Published on Web 02/20/2003 3Mg(g) + N2(g) to yield Mg dopant and was located upstream of the Ga-source; the separation was systematically varied to control dopant incorporation (Figure 1A). Fieldemission scanning electron microscopy (FE-SEM) images of GaN NWs prepared at 950 °C using nickel catalyst14 show that essentially all of the GaN NWs grow normal to the sapphire surface with lengths from 10 to 40 μm (Figure 1B). This normal orientation observed for the NWs suggests that substrate-NW epitaxy may be important in defining the growth direction. Similar data were obtained when the MgGa source separation was varied from 1 to 6 in. Transmission electron microscopy (TEM) was used to further characterize the Mg-doped GaN NWs. Low-resolution images show that the NWs have diameters ranging from ca. 20 to 100 nm and, moreover, that the NW ends terminate in nanoscale Ni-based clusters similar in size to the NW diameters. These latter observations suggest strongly that NW growth proceeds via a nanocluster catalyzed vapor-liquidsolid mechanism.1,2 Lattice-resolved images (Figure 1C) and electron diffraction data (Figure 1D) further show that the Mg-doped GaN NWs are single-crystal materials with a 〈0001〉 growth direction and lattice constants (a ) 0.319 and c ) 0.517 nm), in agreement with wurtzite GaN.15 The GaN NW growth direction and orientation is consistent with epitaxial growth from the c-plane sapphire surface; this explanation agrees with results from previous thin film studies where GaN has been shown to grow epitaxially on c-plane sapphire.16 In addition, energy-dispersive X-ray fluorescence (EDX) analysis of GaN NWs showed no Mg, although this is consistent with the instrument sensitivity (ca. 0.5 atomic %) and expected Mg doping levels (<1020 atoms/ cm3 ≈ 0.23 atomic %). Clear evidence for incorporation of active Mg-dopants was obtained, however, from electrical transport measurements. GaN NWs were configured as FETs to investigate the effects of growth parameters on Mg-doping.17 First, we find that the two-terminal resistance varied systematically with the Ga-Mg source separation, d (Figure 2A). The initial decrease and subsequent increase in resistance with decreasing d is consistent with increasing Mg concentration since above an optimal doping level Mg self-compensation occurs.18,19 Second, current (I) versus source-drain voltage (Vsd) and gate voltage (Vg) were recorded to determine the sign of the carriers produced by the Mg dopant. The data exhibit a conductance increase (decrease) for Vg less (greater) than zero (Figure 2B) and thus demonstrate that the Mg-doped GaN NWs are p-type. Results from different samples further show that NWs prepared with Ga-Mg source separations from 1 to 4 in. are p-type, although larger values of d, which yield lower concentrations of Mg, lead to n-type materials. These observations are consistent with the significant n-type doping due to nitrogen vacancies and/or oxygen impurities in as-grown GaN NWs,11 since these “intrinsic” dopants must be compensated (by Mg) before p-type behavior is observed. In addition, we examined in more detail the transport characteristics of FETs based on optimally doped p-GaN NW (i.e., samples with minimum resistance at d ) 3 in.) to determine hole mobilities. A representative conductance versus Vg plot (Figure 2C) exhibits a relatively sharp onset, steep increase, and finally saturation in the conductance with decreasing Vg. The hole mobility estimated from these data is 12 cm2/V‚s.20 We believe that this value likely represents a lower bound on the possible mobility in p-GaN NWs (e.g., factors such as dopant activation, gate dielectric, and contact formation have not been optimized), although it is nevertheless comparable to the best values, 10 cm2/V‚s, reported for planar p-GaN devices.21 Last, these new p-GaN NWs together with n-GaN materials have been exploited to assemble complementary crossed NW p-n structures (Figure 3A). Transport measurements made on crossed NW p-n junctions show well-defined current rectification that is characteristic of p-n diodes (Figure 3B). Specifically, little current is observed in reverse bias to Vsd ≈ -5 V, and there is a sharp current turn-on in forward bias at ca. 3.5 V. The I-V data recorded from the individual p-GaN and n-GaN NWs were symmetric (inset, Figure 1. (A) Schematic of growth apparatus, where the separation between Ga and Mg3N2 sources is d. The Ga source was fixed at a distance of 0.5 in. upstream from the substrate. (B) FE-SEM images of as grown GaN NWs on c-plane sapphire substrate. Scale bars are 10 μm. (C) Lattice-resolved TEM image of a single 20 nm diameter GaN NW. The black arrow highlights NW axis, which corresponds to the 〈0001〉 direction; the scale bar is 5 nm. (D) Electron diffraction pattern recorded along the [101h0] zone axis with (hkl) indices shown. 344 Nano Lett., Vol. 3, No. 3, 2003 Figure 3B), and thus we can attribute the rectification to the crossed NW p-n junction and not to NW-metal contacts. In addition, the current turn-on at 3.5 V is consistent with the band-gap for GaN in this p-GaN/n-GaN device and contrasts the much lower current turn-on voltage for p-Si/ n-GaN heterojunctions.11 Significantly, optical studies demonstrate that these crossed GaN NW p-n junctions exhibit UV-blue light emission in forward bias. Electroluminescence (EL) measurements on individual crossed GaN NW p-n diodes made using a homebuilt, far-field epifluorescence microscope show that emission is localized at the nanowire cross point and is thus consistent with EL from the forward biased p-n nanojunctions (inset, Figure 3C). EL spectra recorded from forward biased nanoscale p-n junction exhibit a dominant emission peak centered at 415 nm and a smaller peak at ca. 493 nm (Figure 3C). Previous studies of planar LEDs suggest that the 415 nm EL peak can be attributed to radiative recombination from the conduction band to deep levels associated with the Mg dopants,22 while the 493 nm peak is due to recombination from other impurity levels. We also find that at higher injection currents the p-n diodes exhibit UV band-edge emission at ca. 380 nm that is similar to strongly driven planar GaN LEDs.9 Future investigations of individual pand n-GaN NWs and crossed NW junction properties should enable further improvements in these UV nanoscale LEDs, although we believe that these nanodevices represent unique photonic sources even in their present form. Figure 2. (A) Resistance of as grown p-GaN NWs versus d. (B) I-Vsd data for a p-GaN NW prepared with d ) 3 in. The Vg are -2 (red), 0 (black), and +2 V (blue). (inset) FE-SEM image of a representative p-GaN NW device. Scale bar is 1 μm. (C) Conductance versus Vg for the device shown in (B). Figure 3. (A) FE-SEM image of a crossed GaN NW p-n device. Scale bar is 2 μm. (B) I-V data recorded for the p-GaN/n-GaN crossed NW junction. (inset) I-V data for the n-GaN NW (blue) and the p-GaN NW (red). (B) EL spectra recorded from a p-GaN/ n-GaN crossed NW junction in forward bias. The red, yellow, green, and blue EL spectra were recorded with injection currents of 61, 132, 224, and 344 nA, respectively. (inset) Image of the emission from the crossed NW junction. Nano Lett., Vol. 3, No. 3, 2003 345 In summary, p-type single-crystal GaN NWs have been synthesized via metal-catalyzed chemical vapor deposition using Mg as the dopant. NWs prepared on c-plane sapphire substrates grow epitaxially with a 〈0001〉 growth direction. Gate-voltage dependent studies of individual Mg-doped GaN NWs configured as field-effect transistors (FETs) demonstrated unambiguously that the NWs are p-type with maximum hole mobilities of ca. 12 cm2/V‚s. In addition, transport studies of crossed GaN NW structures assembled from pand n-type materials show that the nanoscale junctions behave as well-defined p-n diodes, and significantly, these p-n crossed NW junctions function as nanoscale UV-blue LEDs. We believe that the realization of p-type doping in GaN NWs opens up significant potential for the assembly of nanoscale electronics and photonics. Acknowledgment. We thank L. Z. Yuan and C. Y. Wen for assistance with TEM measurements. C.M.L. acknowledges the Air Force Office of Scientific Research for generous support of this work.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Synthesis of Serrated GaN Nanowires for Hydrogen Gas Sensors Applications by Plasma-Assisted Vapor Phase Deposition Method

Nowadays, the semiconductor nanowires (NWs) typically used in hydrogen gas sensors. Gallium nitride (GaN) with a wide band gap of 3.4 eV, is one of the best semiconductors for this function. NWs surface roughness have important role in gas sensors performance. In this research, GaN NWs have been synthesized on Si substrate by plasma-assisted vapor phase deposition at different deposition time, ...

متن کامل

Giant piezoelectric size effects in zinc oxide and gallium nitride nanowires. A first principles investigation.

Nanowires made of materials with noncentrosymmetric crystal structure are under investigation for their piezoelectric properties and suitability as building blocks for next-generation self-powered nanodevices. In this work, we investigate the size dependence of piezoelectric coefficients in nanowires of two such materials - zinc oxide and gallium nitride. Nanowires, oriented along their polar a...

متن کامل

Electronic and structural characteristics of zinc-blende wurtzite biphasic homostructure GaN nanowires.

We report a new biphasic crystalline wurtzite/zinc-blende homostructure in gallium nitride nanowires. Cathodoluminescence was used to quantitatively measure the wurtzite and zinc-blende band gaps. High-resolution transmission electron microscopy was used to identify distinct wurtzite and zinc-blende crystalline phases within single nanowires through the use of selected area electron diffraction...

متن کامل

Quantum confinement effects in gallium nitride nanostructures: ab initio investigations.

We present ab initio density functional investigations of the atomic and electronic structure of gallium nitride nanodots and nanowires. With increasing diameter, the average Ga-N bond length in the nanostructures increases, as does the relative stability (heat of formation), approaching the values for bulk GaN. As the diameter decreases, the band gap increases, with the variation for the nanod...

متن کامل

Bulk synthesis of a-SixNyH and a-SixOy straight and coiled nanowires{

We report the bulk synthesis of hydrogenated, amorphous SixNy and SixOy nanowires using pools of molten gallium as the solvent medium and microwave plasma consisting of silane in nitrogen and silane in oxygen respectively. High densities of multiple nanowires nucleated and grew from molten gallium pools. The resulting nanowires were tens of nanometers in diameter and tens of microns long. Elect...

متن کامل

The Effect of Aluminum, Gallium, Indium- Doping on the Zigzag (5, 0) Boron-Nitride Nanotubes: DFT, NMR, Vibrational, Thermodynamic Parameters and Electrostatic Potential Map with Electrophilicity Studies

Influence of Aluminum, Gallium, Indium- Doping on the Boron-Nitride Nanotubes (BNNTs) investigated with density functional theory (DFT) and Hartreefock (HF) methods. For this purpose, the chemical shift of difference atomic nucleus was studied using the gauge included atomic orbital (GIAO) approch. In the following, structural parameter values, electrostatic potential, thermodynamic parameters,...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2003