An experimental method to study high speed sliding characteristics during forward and reverse slip

نویسندگان

  • Shashi Rajagopalan
  • Vikas Prakash
چکیده

This paper introduces an experimental technique to investigate dynamic friction characteristics of sliding interfaces at normal pressures up to 125 MPa, slip speeds up to 15 m/s and slip distances of approximately 10 mm. This new apparatus involves a novel modification of the conventional torsional Kolsky bar apparatus employed extensively in the past to investigate high-strain-rate behavior of engineering materials. The experimental configuration allows critical frictional parameters such as the friction-stress, slip speed and slip displacement to be resolved on a micro-second time scale without the use of transducers at the frictional interface. Moreover, the experiment provides information on the evolution of dynamic friction stress during forward as well as reverse slip. Using this experimental configuration dynamic friction experiments were conducted on 6061-Al (T6)/1018 steel and 7075-Al (T6)/toolsteel (D3) tribo-pairs. The results of experiments on 6061-Al (T6)/1018 steel indicate that steady-state kinetic friction is obtained within the rise time of the torsional loading pulse. The coefficient of kinetic friction is observed to increase with the roughness of the tribo-pair surfaces. For a soft/hard tribo-pair interface (7075 Al/tool-steel (D3)) the surface roughness of the harder material (tool-steel (D3)) constituting the tribo-pair is observed to control the frictional force. The measured coefficient of kinetic friction is approximately independent of the interfacial slip velocity for sliding velocities in the range of 2–10 m/s and normal pressures of approximately 100 MPa. Moreover, it is observed that the dynamic friction stress during reverse slip is almost twice as large when compared to friction stress in the forward direction. This increase in friction stress is understood to be due to frictional contact between fresh metallic surfaces formed by the breakdown of oxide and other surface films and anisotropy in frictional surfaces developed during the forward slip. © 2001 Published by Elsevier Science B.V.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Non-Singular Terminal Sliding Mode Control of a Nonholonomic Wheeled Mobile Robots Using Fuzzy Based Tyre Force Estimator

This paper, proposes a methodology to implement a suitable nonsingular terminal sliding mode controller associated with the output feedback control to achieve a successful trajectory tracking of a non-holonomic wheeled mobile robot in presence of longitudinal and lateral slip accompanied. This implementation offers a relatively faster and high precision tracking performance. We investigate this...

متن کامل

Energy-Based Adaptive Sliding Mode Speed Control for Switched Reluctance Motor Drive

Torque ripple minimization of switched reluctance motor drives is a major subject based on these drives’ extensive use in the industry. In this paper, by using a well-known cascaded torque control structure and taking the machine physical structure characteristics into account, the proposed energy-based (passivity-based) adaptive sliding algorithm derived from the view point of energy dissipati...

متن کامل

Dynamic Analysis of a High Load, High-speed Actuator for Rock Deformation Experimentation

Experimental investigation of the sliding-velocity dependence of friction in rock is necessary to understand slip instability and earthquake phenomena, but a capability to conduct sliding friction experiments at high normal loads and at earthquake slip rates (1 m/s) must be developed. Velocitydependent friction is ideally studied by imposing step-wise changes in rate of sliding. Velocity steps ...

متن کامل

An Experimental formulation for PFI injector penetration length versus time and pressure using high speed spray imaging results

Recently, there have been problems with particulate matter pollution in diesel engines and it has reduced production rate of these engines and also, it has accelerated the development of new technologies for PFI and GDI gasoline engines. The spray characteristics has significant impact on the combustion efficiency, power and emissions on internal combustion engines. In This study, effect of inj...

متن کامل

Design and Implementaion of Interior Permanent Magnet Synchronous Motor (IPMSM) Control based on Integral Terminal Sliding Mode Technique

Permanent Magnet Synchronous Motor because of high energy storage capability is very important in electrical drive industry. Speed control of this motor suffers from parameter variations such as variable inductance. In this paper, The Integral-Terminal Sliding Mode Control (ITSMC) method is used to control the speed (torque) along with d-axis current control. This method is like to classic slid...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2001