The Reversing of Interfaces in Slow Diffusion Processes with Strong Absorption
نویسندگان
چکیده
This paper considers a family of one-dimensional nonlinear diffusion equations with absorption. In particular, the solutions that have interfaces that change their direction of propagation are examined. Although this phenomenon of reversing interfaces has been seen numerically, and some special exact solutions have been obtained, there was previously no analytical insight into how this occurs in the general case. The approach taken here is to seek self-similar solutions local to the interface and local to the reversing time. The analysis is split into two parts, one for the solution prior to the reversing time and the other for the solution after the reversing time. In each case the governing PDE is reduced to an ODE by introducing a self-similar coordinate system. These ODEs do not readily admit any nontrivial exact solutions and so the asymptotic behavior of solutions is studied. By doing this the adjustable parameters, or degrees of freedom, which may be used in a numerical shooting scheme are determined. A numerical algorithm is then proposed to furnish solutions to the ODEs and hence the PDE in the limit of interest. As examples of physical problems in which a PDE of this type may be used as a model the authors study the spreading of a viscous film under gravity and subject to evaporation, the dispersion of a population, and a nonlinear heat conduction problem. The numerical algorithm is demonstrated using these examples. Results are also given on the possible existence of self-similar solutions and types of reversing behavior that can be exhibited by PDEs in the family of interest.
منابع مشابه
Self-Similar Solutions for Reversing Interfaces in the Slow Diffusion Equation with Strong Absorption
We consider the slow nonlinear diffusion equation subject to a strong absorption rate and construct local self-similar solutions for reversing (and anti-reversing) interfaces, where an initially advancing (receding) interface gives way to a receding (advancing) one. We use an approach based on invariant manifolds, which allows us to determine the required asymptotic behaviour for small and larg...
متن کاملUsing Experimental Procedure to Improve the Efficiency of the Two Stand Reversing Cold Mill
Production of thin steel strips with 0.18-0.26 mm thickness is about 0.75 of annual production of the two stand reversing cold mill, while its efficiency is 60%. This is due to the fact that after montaging the grinded work rolls, rolling thin steel strips (with thicknesses less than 0.18 millimeters) is unavailable. Initially, unsuitable surface roughness, the friction between rolls and the st...
متن کاملUsing Experimental Procedure to Improve the Efficiency of the Two Stand Reversing Cold Mill
Production of thin steel strips with 0.18-0.26 mm thickness is about 0.75 of annual production of the two stand reversing cold mill, while its efficiency is 60%. This is due to the fact that after montaging the grinded work rolls, rolling thin steel strips (with thicknesses less than 0.18 millimeters) is unavailable. Initially, unsuitable surface roughness, the friction between rolls and the st...
متن کاملEffect of diffusion bonding temperature on microstructure properties of Zr/Ti interlayer in the diffusion bonded joints of Zr702 to A516 steel
In this study, the effect of temperature on the microstructure and reactive layer at the interface between the Ti interlayer and the base metal related to the diffusion bonding of Zr702 to A516 low alloy steel was investigated. The joining was done using the spark plasma sintering technique at temperatures of 900, 950 and 1000°C for 30 minutes. Field Emission Scanning Electron Microscope (FESEM...
متن کاملEffect of diffusion bonding temperature on microstructure properties of Zr/Ti interlayer in the diffusion bonded joints of Zr702 to A516 steel
In this study, the effect of temperature on the microstructure and reactive layer at the interface between the Ti interlayer and the base metal related to the diffusion bonding of Zr702 to A516 low alloy steel was investigated. The joining was done using the spark plasma sintering technique at temperatures of 900, 950 and 1000°C for 30 minutes. Field Emission Scanning Electron Microscope (FESEM...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
عنوان ژورنال:
- SIAM Journal of Applied Mathematics
دوره 72 شماره
صفحات -
تاریخ انتشار 2012