High Voltage Test Apparatus for a Neutron EDM Experiment and Lower Limit on the Dielectric Strength of Liquid Helium at Large Volumes
نویسندگان
چکیده
A new search for a permanent electric dipole moment (EDM) of the neutron is underway using ultracold neutrons produced and held in a bath of superfluid helium. Attaining the target sensitivity requires maintaining an electric field of several tens of kilovolts per centimeter across the experimental cell, which is nominally 7.5 cm wide and will contain about 4 liters of superfluid. The electrical properties of liquid helium are expected to be sufficient to meet the design goals, but little is known about these properties for volumes and electrode spacings appropriate to the EDM experiment. Furthermore, direct application of the necessary voltages from an external source to the experimental test cell is impractical. An apparatus to amplify voltages in the liquid helium environment and to test the electrical properties of the liquid for large volumes and electrode spacings has been constructed. The device consists of a large-area parallel plate capacitor immersed in a 200 liter liquid helium dewar. Preliminary results show the breakdown strength of normal state liquid helium is at least 90 kV cm at these volumes, at the helium vapor pressure corresponding to 4.38 K. These fields hold for more than 11 hours with leakage currents less than 170 pA (about 20% of the maximum tolerable in the EDM experiment). The system is also found to be robust against anticipated radiation backgrounds. Preliminary results for superfluid show that fields of at least 30 kV cm can be sustained at the volumes required for the EDM experiment, about 60% of the design goal. These results are likely limited by the low pressure that must be maintained above the superfluid bath.
منابع مشابه
An apparatus for studying electrical breakdown in liquid helium at 0.4 K and testing electrode materials for the neutron electric dipole moment experiment at the Spallation Neutron Source.
We have constructed an apparatus to study DC electrical breakdown in liquid helium at temperatures as low as 0.4 K and at pressures between the saturated vapor pressure and ∼600 Torr. The apparatus can house a set of electrodes that are 12 cm in diameter with a gap of 1-2 cm between them, and a potential up to ±50 kV can be applied to each electrode. Initial results demonstrated that it is poss...
متن کاملThe Ballistic Behavior of High Strength, Low Alloy-100 Steel at Sub-zero Temperatures
The ballistic response of the high strength, low alloy (HSLA-100) steel at ambient and temperatures of -400°C, -800°C and -1960°C is investigated in this work. Lambert-jonas equation is used to fit the experimental results into a curve. The effect of quenching on ballistic behavior of HSLA-100 is also studied. The experiments are conducted on 3mm thick rectangular specimens impacted by blunt ti...
متن کاملPermeability of Two Clayey Soils Exposed to Petroleum Products and Organic Solvents
Clayey soils are the most common material used for water sealing and undertake an important role in controlling landfill-related pollution. Organic liquids can adversely affect the effectiveness of clay liners by drastically increasing their hydraulic conductivity. The aim of this study is to investigate and compare the permeability in two types of clay with different plasticity, exposed to the...
متن کاملPongamia pinnata Plant Seed Oil as Dielectric Fluid for Electro Discharge Machining Process
Electro Discharge Machining (EDM) is a noticeable machining practice among created unconventional machining procedures for intricate, complex profiles in "hard to machine" materials, similar to heat-treated steels, composites, superalloys, ceramics, composites, carbides, and so on. In EDM, the material expulsion of the cathode is accomplished through precise controlled electric discharge (the s...
متن کاملPlans for a Neutron EDM Experiment at SNS
The electric dipole moment of the neutron, leptons, and atoms provide a unique window to Physics Beyond the Standard Model. We are currently developing a new neutron EDM experiment (the nEDM Experiment) [4]. This experiment, which will be run at the 8.9 Å Neutron Line at the Fundamental Neutron Physics Beamline (FNPB) at the Spallation Neutron Source (SNS) at the Oak Ridge National Laboratory, ...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
عنوان ژورنال:
دوره شماره
صفحات -
تاریخ انتشار 2006