EUROPEAN ORGANIZATION FOR NUCLEAR RESEARCH CERN–PS/2000–011 (AE) June 15, 2000 DESIGN OF A 2.2 GEV ACCUMULATOR AND COMPRESSOR FOR A NEUTRINO FACTORY
نویسندگان
چکیده
The proton driver for a neutrino factory must provide megawatts of beam power at a few GeV, with nanosecond long bunches each containing more than 1×1012 protons. Such beam powers are within reach of a high-energy linac, but the required time structure cannot be provided without accumulation and compression. The option of a linac-based 2.2 GeV proton driver has been studied at CERN, taking into account the space charge and stability problems which make beam accumulation and bunch compression difficult at such a low-energy. A solution featuring two rings of approximately 1 km circumference has been worked out and is described in this paper. The subjects deserving further investigation are outlined. 7 European Particle Accelerator Conference 26 th 30 th June 2000 Vienna, AUSTRIA DESIGN OF A 2.2 GEV ACCUMULATOR AND COMPRESSOR FOR A NEUTRINO FACTORY B. Autin, R. Cappi, M. Chanel, J. Gareyte, R. Garoby, M. Giovannozzi, H. Haseroth, M. Martini, E. Métral, D. Möhl, K. Schindl, H. Schönauer, CERN, Geneva, Switzerland I. Hofmann, GSI, Darmstadt, Germany C. Prior, G. Rees, RAL, Chilton, Didcot, U. K. S. Koscielniak, TRIUMF, Vancouver, Canada
منابع مشابه
EUROPEAN ORGANIZATION FOR NUCLEAR RESEARCH PS/AE Note 2001–001 CERN-NUFACT Note 061 Transfer Line Between the Proton Driver Accumulator and Compressor Rings for the CERN Neutrino Factory
This note presents a possible design for the transfer line between the proton driver accumulator and compressor rings of the CERN Neutrino Factory. Based on the layout of the two rings presented in Ref. [1], a possible configuration for the transfer line is studied. The geometry and the optics of such a transport system are discussed in details.
متن کاملEuropean Organisation for Nuclear Research Cern - Ps Division
In view of a possible evolution of the CERN accelerator complex towards higher proton intensities, a 2.2 GeV H linac with 4 MW beam power has been designed, for use in connection with an accumulator and compressor ring as proton driver of a muon-based Neutrino Factory. The high-energy part of this linac can use most of the RF equipment (superconducting cavities and klystrons) from the LEP colli...
متن کاملEuropean Organization for Nuclear Research Cern - Ps Division Cern/ps 2002-033 (ae) Lattice Design Studies for the Cern Proton Driver Accumulator and Compressor
The CERN baseline scenario for a Neutrino Factory comprises accumulation and compression of the beam delivered by a 2.2 GeV kinetic energy H− linac, to provide the time structure needed on the target. Originally, accumulation and bunch compression in one single ring was envisaged. To limit the RF voltage necessary for bunch rotation, quasi-isochronous lattices were studied. The low transition e...
متن کاملA 40-80 MHz system for phase rotation and cooling
Introduction In this note a scheme for the collection, phase rotation and cooling of muons for a neutrino factory is reported. The scheme is sufficiently generic to be site independent also if some particular choices are influenced by the CERN design. The system discussed in this note is worked on as a possible alternative to the induction linac scheme [1]. The results presented assume the foll...
متن کاملEuropean Organization for Nuclear Research Cern - Ps Division Cern/ps 2001-055 (rf) Nufact Note 089 Status of European Studies for a Neutrino Factory at Cern
Studies for a Neutrino Factory at CERN have made remarkable progress during the last year, supported by specialists from numerous laboratories in Europe and in close connection with teams looking at similar projects in the USA and in Japan. Although many options are still open, a reference scheme is pursued and work has advanced on many on its components. The status of these studies is describe...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
عنوان ژورنال:
دوره شماره
صفحات -
تاریخ انتشار 2002