Adhesive permeability affects coupling of resin cements that utilise self-etching primers to dentine.
نویسندگان
چکیده
OBJECTIVES To examine the effects of an experimental bonding technique that reduces the permeability of the adhesive layer on the coupling of resin cements to dentine. METHODS Extracted human third molars had their mid to deep dentin surface exposed flat by transversally sectioning the crowns. Resin composite overlays were constructed and cemented to the surfaces using either Panavia F (Kuraray) or Bistite II DC (Tokuyama) resin cements mediated by their respective one-step or two-step self-etch adhesives. Experimental groups were prepared in the same way, except that the additional layer of a low-viscosity bonding resin (LVBR, Scotchbond Multi-Purpose Plus, 3M ESPE) was placed on the bonded dentine surface before luting the overlays with the respective resin cements. The bonded assemblies were stored for 24 h in water at 37 degrees C and subsequently prepared for microtensile bond strength testing. Beams of approximately 0.8 mm(2) were tested in tension at 0.5 mm/min in a universal tester. Fractured surfaces were examined under scanning electron microscopy (SEM). Additional specimens were prepared and examined with TEM using a silver nitrate-staining technique. RESULTS Two-way ANOVA showed significant interactions between materials and bonding protocols (p<0.05). When bonded according to manufacturer's directions, Panavia F produced bond strengths that were significantly lower than Bistite II DC (p<0.05). The placement of an additional layer of a LVBR improved significantly the bond strengths of Panavia F (p<0.05), but not of Bistite II DC (p>0.05). SEM observation of the fractured surfaces in Panavia F showed rosette-like features that were exclusive for specimens bonded according to manufacturer's directions. Such features corresponded well with the ultrastructure of the interfaces that showed more nanoleakage associated with the more permeable adhesive interface. The application of the additional layer of the LVBR reduced the amount of silver impregnation for both adhesives suggesting that reduced permeability of the adhesives resulted in improved coupling of the resin cements to dentin. CONCLUSIONS Placement of an intermediate layer of a LVBR between the bonded dentine surface and the resin cements resulted in improved coupling of Panavia F to dentine.
منابع مشابه
Limited decalcification/diffusion of self-adhesive cements into dentin.
Resin cement diffusion into dentin may differ as a function of the pre-treatment regimen. Since self-adhesive cements do not require substrate pre-treatment for luting, penetration of and interaction with the underlying dentin are questioned. We hypothesized that differences in the resin cement diffusion into dentin may exist among current commercial adhesive cements. Composite cylinders were l...
متن کاملFactors contributing to the incompatibility between new adhesive systems and various composite resin restorations
Factors contributing to the incompatibility between new adhesive systems and various composite resin restorations Dr. F. Maleknejad* - Dr. H. Moosavi** *- Associate Professor of Operative Dentistry Dept. - Faculty of Dentistry – Mashhad University of Medical Sciences. **- Assistant Professor of Operative Dentistry Dept. - Faculty of Dentistry – Mashhad University of Medical Sciences. ...
متن کاملBonding of self-adhesive resin cements to enamel using different surface treatments: bond strength and etching pattern evaluations.
This study evaluated the shear bond strengths and etching patterns of seven self-adhesive resin cements to human enamel specimens which were subjected to one of the following surface treatments: (1) Polishing with #600 polishing paper; (2) Phosphoric acid; (3) G-Bond one-step adhesive; or (4) Phosphoric acid and G-Bond. After surface treatment, the human incisor specimens were bonded to a resin...
متن کاملMicrotensile Bond Strength of Self-Adhesive Luting Cements to Ceramics
The purpose of this paper was to compare the bond strengths of the self-adhesive luting cements between ceramics and resin cores and examine their relation to the cement thickness. Three self-adhesive luting cements (Smartcem, Maxcem, and G-CEM) and a resin cement (Panavia F 2.0) for control were used in the paper. The thickness of the cements was controlled in approximately 25, 50, 100, or 200...
متن کاملAdhesive Restorations and the Oral Environmental Behaviour
Adhesive restorations are based on the use of materials, which have the capacity to bond tooth effectively. This is possible due to a polymerizing hybrid layer interface created by the use of the Etch&Rinse (ERAs) and self-etching adhesives (SEAs). Bonding using ERAs include the acid-etching removal of the mineral phase from the substrates of enamel and dentine. A hybrid layer results by fillin...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید
ثبت ناماگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید
ورودعنوان ژورنال:
- Journal of dentistry
دوره 32 1 شماره
صفحات -
تاریخ انتشار 2004