Work hardening: past, present, and future--the work programs special interest section national work-hardening outcome study.

نویسندگان

  • L O Niemeyer
  • K Jacobs
  • K Reynolds-Lynch
  • C Bettencourt
  • S Lang
چکیده

OBJECTIVES A review of outcome research conducted between 1982 and 1992 revealed return-to-work rates for industrial rehabilitation programs that ranged from 50% to 88%. Variations in outcome statistics appeared to reflect discrepancies in factors such as type of research design, initial characteristics of the client sample, and clients excluded from the study group. METHOD A work-hardening outcome study involving 36 programs was conducted by the Work Programs Special Interest Section to address questions left unanswered by existing studies regarding (a) rates of program nonacceptance or noncompletion, (b) basic client characteristics and outcome, (c) length of disability and outcome, (d) breakdown of client disposition after program completion, and (e) program characteristics and return to work. RESULTS Findings included the following: (a) 11.5% of clients were not accepted into work hardening and 24.6% did not complete the program; (b) outcome was not related to client age, gender, area of injury, or physical demand level of job before injury; (c) as duration of disability increased, return to work decreased significantly; (d) at discharge, 48.2% of clients returned to the usual and customary job and 30.5% to alternate or modified work, whereas 13.6% were referred to a vocational counselor; and (e) there was no relationship between number of visits or number of professionals seen and return to work. CONCLUSION The authors suggest a need for uniform standards in collection of outcome data to establish a basis for comparison of efficacy among programs. Recommendations include tracking comparison or control groups, grouping clients in terms of length of disability, computing success rate on the basis of number of clients who completed their program, using relevant subcategories when reporting return to work, and consistency of the postdischarge interval for follow-up.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

On the Optimum Die Shape in Rod Drawing Process Considering Work-Hardening Effect of Material

The assessment of the influence of the work-hardening of material on the optimum die profile and drawing force  in rod drawing process is the main objective of the present paper. The upper bound solution, based on the assumption of perfect plasticity, has been extended to consider the work-hardening of the material during the rod drawing process through curved dies. Analytical results of drawin...

متن کامل

On the optimum die angle in rod drawing process considering strain-hardening effect of material

In this paper, rod drawing process of strain-hardening materials is investigated by analytical, numerical and experimental methods. The classic upper bound solution, based on the assumption of perfect plasticity, has been extended to consider the work-hardening of the material during the drawing process. For a given process conditions and mechanical properties of the rod material, the power ter...

متن کامل

Improvement of Mechanical Properties and Work-Hardening Behavior of Intercritically Annealed Dual Phase Steel

The effect of the initial microstructure and intercritical annealing on mechanical properties and work-hardening response of a high-formability low carbon steel were studied. The work-hardening analysis was based on the modified Crussard–Jaoul method. The ferritic-pearlitic sheets showed low strength and high total elongation with the appearance of the yield point phenomenon. The occurrence of ...

متن کامل

An Investigation Into the Effects of Friction and Anisotropy Coefficients and Work Hardening Exponent on Deep Drawing With FEM

Large strains, anisotropy of mechanical properties of materials and Coulomb friction in contact regions are some properties in the analysis of deep drawing process. In this research, the effects of different parameters such as anisotropy coefficient, work hardening exponent and friction coefficient on deep drawing process of drawing quality steel are studied. For this purpose, the finite elemen...

متن کامل

Profiling the work-hardening therapist: education and experience.

The American.!oumal of' Occupational FhemjJ)' W ork.hardening concepts and techniques originated in occupational therapy (West & McNary, 1956). Occupational therapy's use of activity as a primary modality and its activity analysis of the phYSical and psychosocial components of an occupation substantiate its involvement in work-hardening programs (Harvey-Krefting, 1985). The profession's philoso...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • The American journal of occupational therapy : official publication of the American Occupational Therapy Association

دوره 48 4  شماره 

صفحات  -

تاریخ انتشار 1994