Fuel electrode supported microtubular solid oxide fuel cells (SOFC) fabricated at ICMA have been characterized in both solid oxide steam electrolyser (SOEC) and fuel cell modes. The cells consists of a fuel electrode supporting tube of Ni/YSZ with 40% porosity, 400 μm thickness, 2.4 mm diameter and 100-150 mm length, a 15 m thick YSZ electrolyte and a 50vol% LSM/YSZ composite air electrode of...

In this study, surface morphology control ions in a precursor solution and patterning the YSZ film has been carried out during deposition of thin film from a precursor solution by applying the electrical field for deposition and the pulsed electrical field. The precursor solution was mixed them of ZrO(NO3)4, Y(NO3)3 -6H2O into deionized water, and then was controlled nearly pH3 by adding NH3(aq...

The electrochemical deposition of Cu into 0.12 cm and 60 μm thick, highly porous 65 vol % Ni/yttriastabilized zirconia (YSZ) cermets was investigated. An electrochemical cell in which the electrolyte solution was allowed to flow through a porous Ni/YSZ substrate was used to eliminate mass-transfer limitations and to determine the conditions for which the potential drop in the electrolyte soluti...

 This study aimed to investigate the impact of N-vinylcaprolactam (NVC) and Nano-sized yttria-stabilized zirconia (YSZ), separately and simultaneously, on the mechanical properties of the commercial glass ionomer cements (GICs). Methods: The NVC is able to ameliorate the mechanical and surface properties of glass ionomers; however, its effect hasn’t been investigated in conjunc...

This paper describes a new multilayer TBC that incorporates a 10 μm-thick oxygen barrier layer of yttrium–aluminum garnet (YAG) into a typical YSZ TBC system. The thermal conductivity of as-sprayed YAG/YSZ coatings was reduced due to excessive porosity and amorphous areas in the YAG layer. After long-term heat treatments, the conductivity of the multilayer was unaffected by the presence of YAG....

The combined phase-inversion and sintering method not only produces ceramic hollow fibre membranes with much lower fabrication costs than conventional methods, but these membranes can also be designed to have greatly reduced transport resistances for filtration processes. The bottleneck of this technique is the weak mechanical property of the fibres, due to the small dimensions and the brittle ...

A one-dimensional button-cell model is developed and applied to explore the influence of anode microstructure on solid oxide fuel cell (SOFC) performance. The model couples porous-media gas transport and elementary electrochemical kinetics within a porous Ni-YSZ cermet anode, a dense YSZ electrolyte membrane and a composite LSM-YSZ cathode. In all cases the fuel is humidified H2 and air is the ...

The effect of an 80 nm YSZ interfacial layer, deposited onto a YSZ pellet by different techniques (dip-coating, sputtering and atomic layer deposition) at the SOFC cathode/electrolyte interface to allow a maximum adhesion of the thick cathode layer, was thoroughly analysed. The LSM cathode was deposited on the solid electrolyte by painting and sintered in air at 1200°C for 2 h. The morphologica...

Functionally graded materials (FGM) in the form of layered structure consisting of yttria stabilized zirconia (8 mol% Y2O3) and nickel were fabricated by spark plasma sintering procedure. The relative density, linear shrinkage and Vickers hardness of each layer of graded materials were measured. The microstructure and the composition of these components were studied. The results obtained show t...

Crystalline yttria-stabilized zirconia oxide (YSZ) film was successfully deposited on a silicon wafer without an interfacial amorphous SiO2 layer. The film with equivalent oxide thickness teox down to 1.77 nm shows negligible hysteresis and low interface state density, less than 3 × 1011 cm−2 eV−1. The leakage current density for teox = 1.77 nm film, 1.5 × 10−5 A cm−2 at 1 V bias voltage, is fi...