The corrosion behavior of three sorts of refractories based on alumina-graphite were studied by immersion tests. The melts included smelting reduction molten slag and corresponding carbon saturated molten iron. The influence of test temperature, FeO content in slag and specimen rotative velocity on the corrosion rate of refractories was examined. By means of SEM and EDS, the microstructure chan...

A systematic study on the influence of functionality on adsorption of benzoate and phthalate at -alumina–water interface was investigated. Kinetics of adsorption of benzoate and phthalate on -alumina surfaces were performed at constant ionic strength, I= 5× 10−4 mol dm−3 and pH 5 at 25, 30 and 40 ◦C. Kinetics results show that the rate of adsorption of phthalate is ≈2 times more than that of be...

The objective of this study was to clarify the effects of silane coupling agents and solutions of different polarity on polymethyl methacrylate (PMMA) bonding to alumina. Three silane coupling agents (3-methacryloxypropyltrimethoxysilane (MPS),3-aminopropyltriethoxysilane (APS) and N-2 (aminoethyl) 3-aminopropyltriethoxysilane) and 3 different polar solutions, 70% ethanol, isopropanol and tolue...

The long-term durability of polyethylene lining total hip arthroplasty (THA) mainly depends on periprosthetic osteolysis due to wear particles, especially in young active patients. In hip simulator study, reports revealed significant wear reduction of the alumina ceramic-on-polyethylene articulation of THA compared with metal-on-polyethylene bearing surfaces. However, medium to long-term clinic...

The purpose of this study was to evaluate the effects of functional monomers contained in the primers, as well as alumina particle abrasion on bonding between stainless steel and acrylic resin. SUS XM27 steel was primed with one of the following materials; Alloy Primer, Estenia Opaque Primer, M. L. Primer, and Super-Bond Liquid. Steel disks were either ground flat or alumina-blasted, primed wit...

A taper-fiber SERS nanoprobe modified by gold nanoparticles (Au-NPs) with ultrathin alumina layers was fabricated and its ability to perform remote Raman detection was demonstrated. The taper-fiber nanoprobe (TFNP) with a nanoscale tip size under 80 nm was made by heated pulling combined with the chemical etching method. The Au-NPs were deposited on the TFNP surface with the electrostatic self-...

The surface roughness of the substrate itself could play an important role for the bonding at the interface. In this paper, a correlation of the surface roughness of a rigid alumina substrate and its 2D model of estimated surface area has been studied using Atomic Force Microscopy (AFM). With rougher surface, the adhesive strength between a deposited copper film and the alumina substrate is hig...

The purpose of this study was to investigate the effect of modifying aluminum oxide slips with magnesium oxide (MgO) to create a jointing material for In-Ceram Alumina. Jointed In-Ceram Alumina bars with In-Ceram Alumina slips containing 0-1.0 mass% MgO were examined by a three-point bending test. Joint-free bars were also tested as controls. Fracture surfaces were evaluated by scanning electro...

in this study, preparation of nano-sized gamma alumina with high specific surface area and high yield by thereaction between aluminum nitrate and sodium carbonate, without using any surfactant is reported. bohemite (aluminum oxyhydroxide) was prepared as a precursor by strict control of ph and reaction temperature. the gel produced was purified by washing followed by centrifugation. the specifi...

ÐCommercially available alumina of 94% nominal purity was used to examine the in ̄uence of loading rate on toughening mechanisms. For ®ne-grained alumina, the crack resistance, KR, was found to be independent of crack length and loading rate. Coarse-grained alumina exhibited strongly rising R-curves where the initial fracture toughness, K0, was found to be independent of the loading rate. The ne...