A commercially available Y-TZP ceramic powder was fabricated under four different sintering profiles in order to investigate the effects of conventional single-stage sintering (SSS) with dwell times of 1 min and 2 h, respectively, compared with two-stage sintering (TSS), on the physical and mechanical properties of Y-TZP. Sintering was performed up to 1400 o C at a ramp rate of 10 o C/min. It w...

Lead-free 0.98(Na0.5K0.5)NbO3-0.02Ba(Zr0.52Ti0.48)O3 [0.98NKN-0.02BZT] ceramics were fabricated by the conventional mixed oxide method with sintering temperature at 1,080°C to 1,120°C. The results indicate that the sintering temperature obviously influences the structural and electrical properties of the sample. For the 0.98NKN-0.02BZT ceramics sintered at 1,080°C to 1,120°C, the bulk density i...

This study evaluated the feasibility of using three-dimensional printing (3DP) to fabricate porous titanium implants. Titanium powder was blended with a water-soluble binder material. Green, porous, titanium implants fabricated by 3DP were sintered under protective argon atmosphere at 1,200, 1,300, or 1,400°C. Sintered implant prototypes had uniform shrinkage and no obvious shape distortion aft...

The fraction of municipal solid waste incinerator bottom ash with a particle size less than 8mm has been milled, formed into pellets and rapidly sintered in a rotary furnace at temperatures between 900 and 1080 ◦C. The effect of sintering temperature on density, water absorption and crushing strength has been determined. Sintering at temperatures between 1000 and 1050 ◦C produces pellets with p...

The aim of this study is to investigate the effect of the sintering schedule on microstructure and properties of hydroxyapatite which is produced by different synthesizing methods. Hence, wet-chemical precipitation and solid-state reaction were performed to prepare nano-sized hydroxyapatite (HA) powders. Powders were then uniaxially pressed and sintered by varying temperatures and times. XRD an...

Ellipsometry and mechanically assisted sodium dodecyl sulphate elution was utilized to study the adsorption of human serum albumin (HSA), human immunoglobulin G (IgG), and laminin-1, as well as competitive adsorption from a mixture of these proteins on spin-coated and sintered hydroxyapatite (HA) surfaces, respectively. The HA surfaces were characterized with respect to wettability and roughnes...

Phase change cooling schemes involving passive heat spreading devices, such as heat pipes and vapor chambers, are widely adopted for thermal management of high heat-flux technologies. In this study, carbon nanotubes (CNTs) are fabricated on a 200 lm thick sintered copper powder wick layer using microwave plasma enhanced chemical vapor deposition technique. A physical vapor deposition process is...

CrN/Cu composite powders were synthesized by employing a novel two-step technique. Firstly, the Cr2O3+CuO precursors were prepared by the solution combustion synthesis (SCS) method using cupric nitrate, urea, and chromium nitrate as initial materials. Subsequently, the SCS precursors were calcined at 850 °C in NH3 for 6 h, and transformed to CrN/Cu composite powders. The composite powders consi...

The evolution of microstructure and texture during isochronal annealing of a heavily cold rolled Al–0.3% Cu alloy has been characterized using electron backscatter diffraction. It is found that the rolling texture of this alloy is dominated by the Brass component and that recrystallization during annealing leads to the formation of a pronounced Goss texture. It is suggested that the development...

Electric discharge machining (EDM) is a ‘newer technology utilized to machine hard metals, alloys, composites and ceramics. This paper reports the experimental investigation carried out on EDM to study the effects of machining parameters such as pulsed current on material removal rate, depth of cut, overcut, tool wear (net weight lost) and hardness on En-31 tool steel The work material was elec...