This work extends previous research on numerical solution of nonlinear systems in musical acoustics to the realm of nonlinear musical circuits. Wave digital principles and nonlinear state-space simulators provide two alternative approaches explored in this work. These methods are used to simulate voltage amplification stages typically used in guitar distortion or amplifier circuits. Block level...

WSN is wireless sensor network which consist of numbers of nodes. Transceiver has main role in WSN node. Transceiver consists of both transmitter as well as receiver. Power amplifier, low noise amplifier, mixer, voltage control oscillator are the main block of Transceiver. Power amplifiers are a key part of RF transmitters. 2.4 GHz RF CMOS power amplifier implemented with SMIC 0.13μm is propose...

We experimentally demonstrate that a type-II pulsed optical parametric amplifier operated in a phaseinsensitive configuration works as a near-perfect classical optical amplifier whose noise figure approaches 3 dB at high gains. We further demonstrate that, when operated in a phase-sensitive configuration, this amplifier works as a quantum-optical amplifier whose noise figure goes below 3 dB and...

In this paper the actuation system, often encountered high-precision motion systems, is studied. To find out the limitations of the actuation system, a integrated electromechanical model of the amplifier, actuator and mechanics is derived. This is done in a system’s theory-approach, so that amplifier feedback circuit design can be tuned using loop-shaping techniques. Stability analysis is carri...

This paper presents the design, fabrication and performance of a three-stage 155GHz monolithic low noise amplifier (LNA) using 0.1 -pm pseudomorphic (PM) InAIAs/InGaAs/InP HEMT technology. This amplifier exhibits a measured small signal gain of 12 dB at 155 GHz, and more than 10 dB gain from 151 to 156 GHz. When this amplifier is biased for low noise figure, a noise figure of 5.1 dB with associ...

This paper presents a fixed gain high output power amplifier with performance determined by using on-wafer measurement. The amplifier is fully differential based on inductive load and resistive degeneration which is designed using a 0.18 μm SiGe BiCMOS process. The amplifier achieves power gain of 7.2 dB, 3-dB bandwidth of 2.06 GHz, operating frequency of 12 GHz, power consumption of 12 mW usin...

High Efficiency Power Amplifier for Envelope Detection is presented here in this paper which uses the LDMOS power amplifier to achieve high efficiency. The main objective in this work to design a power amplifier which is more efficient when subject to various kind of situations. QAM modulation with 64 point, and Additive White Gaussian Noise Channel was used here in this work. Amplitude Modulat...

In this paper, a 10-Gb/s inductorless CMOS receiver front end is presented, including a transimpedance amplifier and a limiting amplifier. The transimpedance amplifier incorporates Regulated Cascode (RGC), active-inductor peaking, and intersecting active feedback circuits to achieve a transimpedance gain of 56 dB and a bandwidth of 8.27 GHz with a power dissipation of 35 mW. The limiting amplif...

In this paper two different Gm-C chopper amplifiers, aimed for signal amplification in implantable devices are presented. The first one is a pre-amplifier for ENG signals that was fabricated in a 1.5 μm technology. Measurements of this amplifier showed input noise of 1.2 nVHz and 2.5 μV offset with a power consumption of 28 mW. The second is a complete amplifier for EEG signals designed in a 0....

0 1 5 Frequency [GHz] 6 2 3 4 Abstract The validity of lumped element microwave class-F amplifier circuit design has been demonstrated experimentally. By means of the proposed class-F amplifier design method, more than 4th-order higher harmonic frequencies can be taken into account in class-F microwave amplifier design using only lumped element components. In this approach, miniaturization of c...