A new kind of polymer-based sensor is described in which the experimental parameters controlling selectivity and sensitivity are decoupled. The sensor is based on a surface acoustic wave (SAW) gravimetric transducer modified with a high-surface-area, nanoporous alumina coating. A very thin ( approximately 40 nm) poly(dimethylsiloxane) (PDMS) coating resides atop the porous alumina structure. In...

This work aims at developping a multidisciplinary approach to highlight the correlation between the toxicity of alumina engineered nanoparticles (NP) and their physicochemical characteristics. Accuracy of measurements depends on cell production after contact with particles, but also depends on the ability of biomolecules to get adsorbed on the NP [1]. That’s why, mechanisms of biomolecules adso...

The effect of heat source/sink on steady two-dimensional laminar MHD mixed convection boundary layer flow past a vertical permeable surface embedded in a porous medium saturated by a nanofluid is performed in this study. Numerical solutions of the similarity equations are obtained using the shooting method. Three types of metallic or nonmetallic nanoparticles, namely Copper (Cu), Alumina (Al2O3...

Typical laser-dependent methods such as nanoparticle tracking analysis (NTA) and dynamic light scattering (DLS) are not able to detect nanoparticles in an optically opaque medium due to scattering or absorption of light. Here, the electrochemical technique of 'nano-impacts' was used to detect nanoparticles in solution in the presence of high levels of alumina particulates causing a milky white ...

The development of assemblies consisting of unencapsulated, sub-10-nm gold particles attached to individual carbon nanotubes (CNTs) with diameters of 2 nm is described. The assemblies are formed on the surface of a porous anodic alumina (PAA) template on which the CNTs (single- or double-walled) are grown by plasma-enhanced chemical vapor deposition. The Au nanoparticles are formed through an i...

An analysis of the steady mixed convection boundary layer flow past a vertical permeable surface embedded in a porous medium saturated by a nanofluid is performed in this study. Numerical solutions of the similarity equations are obtained using the shooting method. Three types of metallic or nonmetallic nanoparticles, namely Copper (Cu), Alumina (Al2O3) and Titania (TiO2) are considered by usin...

Al-doped ZnO (AZO) and In-doped ZnO (IZO) nanopowders were prepared by a sol-gel route and subsequent drying in ethanol under supercritical conditions. The morphological and microstructural properties were investigated by transmission electron microscopy (TEM) analysis and X-ray powder diffraction (XRD). The characterization study showed that the AZO and IZO nanoparticles were crystalline and e...

Introduction Most dyes used in the pigmentation of textiles, paper, leather, ceramics, cosmetics, inks and food-processing products are derived from azo dyes, which are characterised by the presence of one or more azo groups (-N=N-) in their structure. Approximately 15% of the dyes produced worldwide are lost within waste water during synthesis and processing. This waste represents a great haza...

Quenching of small stainless steel rods in pure water and nanofluids with alumina and diamond nanoparticles at low concentrations (0.1 vol%) was investigated experimentally. The rods were heated to an initial temperature of ~1000 C and then plunged into the test fluid. The results show that the quenching behavior of the nanofluids is nearly identical to that of pure water. However, due to nano...

An alomina-based nano adsorbent was prepared by modification of the external surface of γ-alumina (γ-Al2O3) nanoparticles with functional groups of a new Schiff base 4-[(2-hydroxy-3-methoxy-benzylidene)-amino]-5-methyl-2,4-dihydro-[1,2.4]triazole-3-thione] “L”. In order to the removal of Cr(VI) from aqueous solutions, we used the reaction of the sodium dodecyl sulfate coated nano-alumina with L...