Zinc oxide (ZnO, n-type) and copper oxide (CuO, p-type) nanowires have been synthesized and preliminarily investigated as innovative materials for the fabrication of a proof-of-concept thermoelectric device. The Seebeck coefficients, electrical conductivity and thermoelectric power factors (TPF) of both semiconductor materials have been determined independently using a custom experimental set-u...

Gas sensors based on tin oxide (SnO2) and palladium doped SnO2 (Pd:SnO2) active materials are fabricated by a laser printing method, i.e. reactive laser-induced forward transfer (rLIFT). Thin films from tin based metal-complex precursors are prepared by spin coating and then laser transferred with high resolution onto sensor structures. The devices fabricated by rLIFT exhibit low ppm sensitivit...

A tin dioxide (SnO2) sensor was fabricated by inkjet printing onto polyimide foil. Gold electrodes and heater were printed on each side of the substrate. A SnO2 based ink was developed by sol-gel method and jetted onto the electrodes. A final annealing at 400°C compatible with the polymeric transducers allowed to synthetize the SnO2 sensing film. Electrical measurements were carried out to char...

The superior performance of metal oxide nanocomposites has introduced them as excellent candidates for emerging energy sources, and attracted significant attention in recent years. The drawback of these materials is their inherent structural pulverization which adversely impacts their performance and makes the rational design of stable nanocomposites a great challenge. In this work, functional ...

In humans, respiratory disorders are common. Today, rapid, risk-free, and potentially low-cost diagnostics of detected in the patient's exhaled air critical. Fractional nitric oxide (FENO), volatile organic molecules, carbon monoxide, hydrocarbons, hydrogen peroxide among inhaled biomarkers mentioned. Breathomics from compounds oximeters also shortly discussed. The use WO3 FENO monitors is They...

[Zn(CH3COO)2 + PVP]/[C2H5O)4Si + PVP]/[SnCl4 + PVP]/[Ti(OC4H9)4 + CH3COOH + PVP] precursor composite fibers have been fabricated through self-made electrospinning equipment via electrospinning technique. ZnO/SiO2/ SnO2/TiO2 composite nanofibers were obtained by calcination of the relevant precursor composite fibers. The samples were characterized by thermogravimetric-differential thermal analys...

Crystalline nanobelts of ZnO and SnO2 were prepared from a thermal evaporation of oxide powders inside an alumina tube in the absence of catalysts. Typical dimensions of the nanobelt samples ranged from approximately 10 to 100 microns in length, 30 to 300 nm in width, and 6 to 30 nm in thickness. Room temperature Raman spectra were obtained on pressed mats of nanobelt samples and compared with ...

Practical, efficient synthesis of metal oxide nanocrystals with good crystallinity and high specific surface area by a modified polymer-network gel method is demonstrated, taking ZnO nanocrystals as an example. A novel stepwise heat treatment yields significant improvement in crystal quality. Such nanophase materials can effectively degrade common organic dyes under solar radiation and can perf...

In this experiment Polystyrene/Zinc-oxide (PS/ZnO) nanocomposite fibers were produced by electrospinning technique using limonene as a green solvent. First, the morphology of electrospun pure polystyrene (PS) and PS/ZnO nanocomposite fibers investigated by SEM. Results showed the PS fiber diameter decreased by increasing concentration of Zinc Oxide nanoparticles (ZnO NPs). Thermo Gravimetric An...

Standard sacrificial template synthesis allows metal oxide nanotubes to be produced from ZnO nanowires. In spite of their high interest in several technological fields, the low surface area of these nanotubes is a drawback for most applications. Here we report for the first time the sacrificial template synthesis of stainless steel wire-mesh (SSWM) supported metal oxides of high technological i...