Phenolic resin-derived activated carbon (AC) cloths are used as electrodes for large scale electric double-layer capacitors (EDLCs) or supercapacitors. To increase the energy and power density of the supercapacitor, the contact resistance between the carbon cloth and the aluminum foil current collector is reduced by modifying the Al current collectors. Different modified Al current collectors, ...

The selection of an appropriate substrate is an important initial step for many studies of electrochemically active materials. In order to help researchers with the substrate selection process, we employ a consistent experimental methodology to evaluate the electrochemical reactivity and stability of seven potential substrate materials for electrocatalyst and photoelectrode evaluation. Using cy...

Al–TiC nanocomposite materials have been prepared by a new in situ synthesizing technique. A mixture of aluminum, titanium, and graphite has been prepared using ball milling technique and then melted in a high frequency induction heat furnace (HFIHF) at different sintering temperatures, namely 900, 1100, and 1300 °C. The effect of sintering temperature on the corrosion of the Al–TiC composite i...

A series of aluminum hypophosphite (AHPi)/graphite-like carbon nitride (g-C₃N₄) (designated as CAHPi) hybrids were prepared, followed by incorporation into thermoplastic polyurethane (TPU). The introduction of CAHPi hybrids into TPU led to a marked reduction in the peak of the heat release rate (pHRR), total heat release, weight loss rate, smoke production rate and total smoke production (TSP)....

Sub-micron sized airborne particulate matter (PM) is not collected well on regular quartz or glass fiber filter papers. We used a micro-orifice uniform deposit impactor (MOUDI) to fractionate PM into six size fractions and deposit it on specially designed high purity thin aluminum disks. The MOUDI separated PM into fractions 56-100 nm, 100-180 nm, 180-320 nm, 320-560 nm, 560-1000 nm, and 1000-1...

Aluminum alloys, which serve as heat sink in light-emitting diode (LED) lighting, are often inherent with a high thermal conductivity, but poor thermal total emissivity. Thus, high emissive coatings on the Al substrate can enhance the thermal dissipation efficiency of radiation. In this study, the ultrasonic mechanical coating and armoring (UMCA) technique was used to insert various ceramic com...

Article history: Received 30 May 2012 Accepted 24 June 2012 Available online 12 August 2012 0026-2714/$ see front matter 2012 Elsevier Ltd. A http://dx.doi.org/10.1016/j.microrel.2012.06.087 ⇑ Tel.: +81 52 612 6111; fax: +81 52 612 5623. E-mail address: [email protected] A power semiconductor module using a bonding film with anisotropic thermal conduction has been studied. The bonding fil...

Submicron to micron size particles are produced in the gas phase of sputtering discharges. These particles can contaminate thin films grown by sputter deposition. On the other hand, particle production in a discharge can be desirable when used for manufacturing fine powders. Here, experimental results are presented demonstrating particle production in an argon discharge, using a variety of targ...

We have investigated the use of aluminum based amorphous metallic glass as the anode in lithium ion rechargeable batteries. Amorphous metallic glasses have no long-range ordered microstructure; the atoms are less closely packed compared to the crystalline alloys of the same compositions; they usually have higher ionic conductivity than crystalline materials, which make rapid lithium diffusion p...

In this study, the interference effects of Al3+, Mg2+, Cl- and SO4(2-) ions on the determination of manganese by graphite furnace atomic absorption spectrometry (GFAAS) were investigated. At first, the interferences caused by Al2(SO4)3, AlCl3, MgCl2 and MgSO4, which are the most possible major compounds for the combinations of the ions mixed, were individually considered. Then, the effects caus...