An artificial neural network (ANN) model is developed for the analysis, simulation, and prediction of the austenite reversion in the thermo-mechanical treatment of 304L austenitic stainless steel. The results of the ANN model are in good agreement with the experimental data. The model is used to predict an appropriate annealing condition for austenite reversion through the martensite to austeni...

The metallic phases of meteorites are predominantly composed of Fe with B to 50 wtR Mi. During slow cooling (10-1 to 103°C per million years) be low 500°C three types of phase transformations take place: 1) Fe—Mi mar tensite (m2) decomposition to c2(ferrite) and y(austenite); 2) Decomposition of austenite to a so—called “cloudy border” of a and ; and 3) Partial ordering of 48 to 55 wtR Mi auste...

The influence of nitrogen (0 to 0.27 wtYo) on martensite formation in an experimental low-nickel stainless-steel alloy (Fe-17Cr-7Mn-4Ni) has been investigated. The alloys containing 0.1 wtYo or more nitrogen are fully austenitic at room temperature; those containing less nitrogen consist of a mixture of austenite, martensite and S-ferrite. The alloys containing less than 0.2 wtYo nitrogen are m...

The characteristics of magnetostructural coupling play a crucial role in the magnetic field-driven behaviour of magnetofunctional alloys. The availability of magnetostructural coupling over a broad temperature range is of great significance for scientific and technological purposes. This work demonstrates that strong magnetostrucural coupling can be achieved over a wide temperature range (222 t...

During the summer of 2006, I had the opportunity to participate in an internship through the U.S. Department of Energy (DOE) at Oak Ridge National Laboratory (ORNL). ORNL is the nations largest national laboratory that is funded by the DOE. ORNL is known best for developing the technology for the atomic bomb and was a classified area for many years. Today ORNL’s research spans all areas of scie...

The stress-induced transformation behavior of retained austenite is considered in this work. With the development of transformationinduced plasticity (TRIP) steels this deformation mode is of growing importance. Twinned martensite structures were calculated using the crystallographic theory of martensite. An available work criterion was used to predict the transformation potentials for 16 diffe...

The medium Mn steels are gaining increasing attention due to their excellent combination of mechanical properties and material cost. A cold-rolled 0.1C5Mn medium Mn steel with a ferrite matrix plus metastable austenite duplex microstructure was resistance spot-welded with various welding currents and times. The nugget size rose with the increase of heat input, but when the welding current excee...

Cryogenic treatment can be used as a supplemental treatment that is performed on some tool steels between quenching and tempering as an effective method for decreasing retained austenite and increasing wear resistance. In this research, the effect of deep cryogenic treatment (DCT) on dimensional stability and mechanical properties of 80CrMo12 5 tool steel was investigated. The martensitic trans...

the quenching and partitioning (q&p;) process is a new heat treatment cycle to produce the third generation of advanced high strength steels based on diffusion of carbon from martensite to retained austenite phase. the application of this process for various steels leads to a remarkable combination of mechanical properties including high strength and good ductility. using this process in automo...

Ni39+x Mn50Sn11-x (x = 0.5, 1.0, 1.5 and 2) alloys comprise multiple martensite nanostrips of nanocrystallites when cast in small discs, for example, ∼15 mm diameter and 8 mm width. A single martensite phase with a L10 tetragonal crystal structure at room temperature can be formed at a critical Sn content of 9.0 at.% (x = 2), whereas an austenite cubic L21 phase turns up at smaller x ⩽ 1.5. The...