نتایج جستجو برای: sintered alumina
تعداد نتایج: 16860 فیلتر نتایج به سال:
The purpose of this study was to investigate the effect of high alumina cement and Sintering temperature on microstructure, physical and mechanical properties of foamed alumina insulation bricks. The Slurry samples were prepared containing 75wt% of alumina and 25% wt of deionised water containing 1%, 3%, 5%, 7% wt% high Alumina cement and 2% wt% foam. Then samples were poured into metal molds....
In the present work, Al2O3-CeO2 composite nanopowders were synthesized via co-precipitation method. The sinterability of the synthesized powders was investigated. The results showed that the transformation of transition phases of alumina to α-Al2O3 takes place at 1200 °C. TEM images showed that the powders was composed of nanoparticles in the range of 30−70 nm. The densification of composites s...
Next to the main aluminium ore, bauxite, an assemblage of aluminium hydroxides, aluminium oxides and other minerals (gibbsite, diaspore, boehmite, kaolinite, quartz, hematite, goethite, rutile, anatase, and alumogel), aluminium oxides find direct application in diverse industrial processes (e.g., refractory, abrasives, and watch-making industries) as well as in the gemstone sector. Corundum (Al...
This report presents the results obtained by the five U.S. participating laboratories in the Versailles Advanced Materials and Standards (VAMAS) round-robin for fracture toughness of advanced ceramics. Three test methods were used: indentation fracture, indentation strength, and single-edge pre-cracked beam. Two materials were tested: a gas-pressure sintered silicon nitride and a zirconia tough...
Spray drying is widely used for producing granulated feed materials for compaction process, which is the current industrial method for manufacturing alumina-zirconia femoral heads. The optimization of the granules compaction behavior requires the control of the slurry rheology. Moreover, for a dual-phase ceramic suspension, the even phase distribution has to be kept through the atomization step...
Alumina composites containing in-situ-formed hexaluminate (LaAl,,018, LaMgAl,,O,,, SrAl12019, and Mg,NaAl,,O,) platelets can be pressureless-sintered to high density. The grain morphology of the aluminates can be controlled by composition. A peak toughness 50% higher than that of alumina is obtained at 30 vol% aluminates, with a modest reduction (10%) in hardness and Young’s modulus. Although c...
The wear resistance of Al2O3/2.5 vol.% Ni nanocomposites sintered by a conventional route was studied under ball-on-disk dry sliding conditions and compared with the same nanocomposites but consolidated by spark plasma sintering, together with alumina obtained by the same technique and by hot pressing. The results showed an improvement of about 0.5, 1 and 2 orders of magnitude, respectively. Th...
OBJECTIVE To assess the 5-year survival of metal-ceramic and all-ceramic tooth-supported fixed dental prostheses (FDPs) and to describe the incidence of biological, technical and esthetic complications. METHODS Medline (PubMed), Embase and Cochrane Central Register of Controlled Trials (CENTRAL) searches (2006-2013) were performed for clinical studies focusing on tooth-supported FDPs with a m...
High-strength all-ceramic materials are commonly used in dentistry. When complications occur in an all-ceramic restoration, the restoration is usually replaced. This article describes the time-saving ability and cost-effectiveness of this novel technique for the addition of a pontic in two complicated clinical cases. Turkom-Cera(™) [Turkom-Ceramic (M) Sdn. Bhd.] with aluminum oxide (99.98%) is ...
نمودار تعداد نتایج جستجو در هر سال
با کلیک روی نمودار نتایج را به سال انتشار فیلتر کنید