The fabrication of the micro-channel array through micro-embossing on an ultrafine-grained (UFG) LZ91 Mg-Li alloy was investigated in this paper. Micro-embossing tests indicated that the depth of the channels increase with increasing temperatures. Micro-array channels with widths ranging from 50 μm to 200 μm were performed with an applied force of 2 kN at 423 K, following by a dwell time of 60 ...

Bulk ultrafine grained (UFG)/nanocrystal metals possess exceptional strength but normally poor ductility and thermal stability, which hinder their practical applications especially in high-temperature environments. Through microalloying strategy that enables the control of grains and precipitations in nanostructured regime, here we design and successfully produce a highly microstructure-stable ...

In the present study, an ultrafine grained (UFG) 304L stainless steel with the average grain size of 300 nm was produced by a combination of cold rolling and annealing. Weldability of the UFG sample was studied by Nd: YAG laser welding under different welding conditions. Taguchi experimental design was used to optimize the effect of frequency, welding time, laser current and laser pulse duratio...

We present the results of in-situ studies of evolution of grain boundary misorientations in ultrafine grained (UFG) aluminum alloy Al-4 Cu-0.5 Zr (wt%) during annealing. The structure of the UFG alloy was obtained by severe plastic deformation method. Misorientations between the grains were measured using single reflection technique. It was found that relaxation processes during annealing are a...

an ultrafine grained dual phase (ufg dp) steel containing niobium was produced by a new routeutilizing simple cold-rolling and subsequent intercritical annealing of ferrite/martensite duplex startingstructures. the effects of intercritical holding time on the microstructural evolutions and mechanicalproperties were studied. the results showed that increasing intercritical holding time enhnaced ...

Microstructures and mechanical properties of equal-channel angular pressing (ECAP) processed and naturally aged ultrafine grained (UFG) and coarse grained (CG) 7075 Al alloys as well as their evolutions during annealing were investigated. After the same natural aging, the tensile yield strength, ultimate strength, and microhardness of the UFG samples were 103%, 35%, and 48% higher, respectively...

We describe here for the first time the low temperature superplasticity of nanostructured low carbon steel (microalloyed with V, N, Mn, Al, Si, and Ni). Low carbon nanograined/ultrafine-grained (NG/UFG) bulk steel was processed using a combination of cold-rolling and annealing of martensite. The complex microstructure of NG/UFG ferrite and 50-80 nm cementite exhibited high thermal stability at ...

At room temperature, the indentation morphologies of crystalline copper with different 13 grain size including nanocrystalline (NC), ultrafine-grained (UFG) and coarse-grained (CG) copper 14 were studied by nanoindentation at the strain rate of 0.04/s without holding time at indentation 15 depth of 2000 nm. As the grain size increasing, the height of the pile-up around the residual 16 indentati...

In this study, we present the detailed investigation of the influence of the etching medium (acidic or basic Piranha solutions) and the etching time on the morphology and surface relief of ultrafine grained (UFG) and coarse grained (CG) titanium. The surface relief and morphology have been studied by means of scanning electron microscopy (SEM), atomic force microscopy (AFM), and the spectral el...

In the present work, new possibilities of the X-ray diffraction for investigations of the 17 phase composition, size, shape and volume fraction of particles in ultrafine-grained (UFG) 18 martensitic steel and the Cu-Cr-Zr alloy have been demonstrated. For the first time, the method of 19 X-ray diffraction in the transmission mode was used to identify particles with a volume fraction of 20 less ...