This paper reports on the simulation of the near-nozzle region of a moderate Reynolds number cold jet flow exhausting from a chevron nozzle. The chevron nozzle considered in this study is the SMC001 nozzle experimentally studied by the researchers at the NASA Glenn Research Center. This nozzle design contains six symmetric chevrons that have a five-degree penetration angle. The flow inside the ...

The bending angle effect on a multi-domain in-plane switching liquid crystal display (MD IPS LCD) using the chevron-shaped electrodes is investigated through a three-dimensional simulation. We find that when the bending angle of the electrodes increases from 10 to 40 , the threshold voltage is lowered from 1.25 Vrms to 0.75 Vrms. With the optimized uniaxial compensation films, the viewing angle...

Celestite/barite−replaced and phosphate−replicated tubes of Early Cambrian anabaritids from the northern part of the Si− berian Platform (Anabar Shield) give new evidence on the wall−structure of these enigmatic fossils. The walls consist of fibres, interpreted as reflecting an original aragonitic fabric. Bundles of fibres are arranged in growth lamellae, and the latter form an angle of at leas...

Introduction: The load-dependent collageneous fiber organization in the joint cartilage determines the biomechanical properties of this tissue. It has been shown that the deformation mechanisms of the collagen network under compressive load depend on the morphological and structural intactness of the cartilage [1, 2]. Thus, the analysis of load-reactions of joint cartilage could be a successful...

Shaoyi Jiang,† Rawls Frazier,‡ Elaine S. Yamaguchi,§ Mario Blanco,† Siddharth Dasgupta,† Yanhua Zhou,† Tahir Cagin,† Yongchun Tang,| and William A. Goddard, III*,† Materials and Process Simulation Center, Beckman Institute (139-74), DiVision of Chemistry and Chemical Engineering, California Institute of Technology, Pasadena, California 91125, CheVron Research and Technology Company, 100 CheVron...

We performed basal chevron metatarsal osteotomy on 32 feet (31 patients) for painful hallux valgus associated with an increased intermetatarsal 1/2 angle (> 12 degrees). Pedobarographic and radiological examinations were done preoperatively and at a minimum of six months postoperatively. The average hallux valgus angle was improved from 40.9 degrees to 19.2 degrees and the intermetatarsal 1/2 a...

PURPOSE The aim of this study was to investigate new point-connecting measurements for the hallux valgus angle (HVA) and the first intermetatarsal angle (IMA), which can reflect the degree of subluxation of the first metatarsophalangeal joint (MTPJ). Also, this study attempted to compare the validity of midline measurements and the new point-connecting measurements for the determination of HVA ...

Introduction Hallux valgus is one of the most common forefoot deformities worldwide. Females are affected more often than males. The three most common clinical symptoms are the painful bunion, transfer metatarsalgia, and hammer or claw toes. Methods This case series consisted of 20 patients who had chevron osteotomy from January 2015 to January 2016. The clinical assessment was measured by The ...

Chevron structures adopted by confined smectic liquid crystals are investigated via molecular dynamics simulations of the Gay-Berne model. The chevrons are formed by quenching nematic films confined between aligning planar substrates whose easy axes have opposing azimuthal components. When the substrates are perfectly smooth, the chevron formed migrates rapidly towards one of the confining wall...

The (relative) energies of symmetric tilt grain boundaries in a strongly segregated lamellar block copolymer are determined by analysis of the dihedral angles at grain-boundary triple junctions. The analysis reveals two regimes: at low and intermediate misorientations (corresponding to a tilt-angle range 0≤θ≤85°) the grain-boundary energy is found to depend on the tilt angle as E(θ)∼θ(x), with ...