The aim of this study was to evaluate the influence of different light sources on the bond strength of indirect resin composite restorations cemented with a dual-cure resin cement. The superficial dentin of human third molars was exposed and acid-etched and an adhesive system was applied (Single Bond 2). Four-mm-thick indirect resin composite restorations (Gradia) were fabricated and cemented u...

Background: The aim of this in vitro study was to investigate the effect different mouthwashes on color stability artificial gingiva material that are used implant retained hybrid prostheses.
 Material and Methods: materials examined terms gingival colored composite (Gradia Plus Gum, GC Europe,Belgium), pink heat polymerised acrylic resin (Meliodent, Heraeus Kulzer, Germany) feldspathic po...

This in vitro study evaluated the coronal and apical marginal microleakage of four self-etch, seventh generation adhesive systems. Sixty non-carious human molars were randomly assigned to four groups (n = 12). Class V cavities were prepared on the facial or lingual surface of each tooth with coronal margins in enamel and apical margins in cementum (dentin) at the cementoenamel junction. The pre...

INTRODUCTION Indirect composites are developed to overcome the shortcomings of direct composites but, the adhesion of resin cements to indirect composites is still difficult. The purpose of this study was to evaluate the surface morphology of indirect resin composite treated by different powers of Er:YAG laser using Scanning Electron Microscopy (SEM). METHODS indirect resin composite blocks (...

BACKGROUND AND AIMS Polishing may increase the surface roughness of composites, with a possible effect on bacterial growth and material properties. This preliminary in vitro study evaluates the effect of three different polishing systems (PoGo polishers, Enhance, Venus Supra) on six direct resin composites (Gradia Direct, Venus, Venus Diamond, Enamel Plus HFO, Tetric Evoceram, Filtek Supreme XT...

The aim of this study was to determine surface roughness and topography of polished dental resin-based nanocomposites. Four representative dental resin-based nanocomposites were tested in the study: two nanohybrids (Filtek Z550 and Tetric EvoCeram) and two nanofilled (Filtek Ultimate Body and Filtek Ultimate Translucent); and two reference materials: one microfilled (Gradia Direct) and one micr...

OBJECTIVE The purpose of this study was to determine the microtensile bond strength of various resin composite/adhesive systems to alumina particle abraded Ti-6Al-4V substrate after aging for 24h, 10 days, and 30 days in distilled water at 37 degrees C. METHODS Four laboratory resin composite veneering systems (Gradia, GR; Solidex, SOL; Ceramage, CER; and Sinfony, SF) were bonded to 25 mm dia...

AIM This study evaluated the bond strength and failure mode of enamel/resin-based composite veneers bonded with three different dual cured resin adhesive systems. METHODS AND MATERIALS Standard preparations for laminate veneer restorations were made on 30 human central incisors using depth cutting burs (0.5 mm depth at the incisal area and 0.3 mm at the gingival area). Thirty indirect laminat...

PURPOSE To investigate the relationship between post and core build-up materials on the fracture resistance of endodontically treated teeth restored with different onlay restorations. METHODS 60 mandibular molars were endodontically treated and divided into three experimental groups that received one of the following onlay restorations: gold onlays, glass ceramic onlays (Empress I), or resin ...

PURPOSE To determine the changes in surface gloss of different composite materials after laboratory toothbrushing simulation. METHODS 36 specimens were fabricated for each material and polished with 120-, 220-, 500-, 1200-, 2400- and 4000-grit SiC abrasive paper, respectively. Gloss measurements were made with a glossmeter (Novocurve) prior to testing procedures and then subjected to simulate...