نتایج جستجو برای: wear modeling steel indentation

تعداد نتایج: 496117  

Journal: :Journal of Research of the National Bureau of Standards 1947

Journal: :J. Computational Design and Engineering 2016
Andrés Bustillo Luis Norberto López de Lacalle Asier Fernández-Valdivielso Pedro Santos

An experimental approach is presented for the measurement of wear that is common in the threading of cold-forged steel. In this work, the first objective is to measure wear on various types of roll taps manufactured to tapping holes in microalloyed HR45 steel. Different geometries and levels of wear are tested and measured. Taking their geometry as the critical factor, the types of forming tap ...

Journal: :Journal of nanoscience and nanotechnology 2010
L Cunha F Vaz C Moura D Munteanu C Ionescu J P Rivière E Le Bourhis

Ti-Si-C thin films were deposited onto silicon, stainless steel and high-speed steel substrates by magnetron sputtering, using different chamber configurations. The composition of the produced films was obtained by Electron Probe Micro-Analysis (EPMA) and the structure by X-ray diffraction (XRD). The hardness and residual stresses were obtained by depth-sensing indentation and substrate deflect...

2012
IAN M. HUTCHINGS

Tlre preserrce oflrarrl corrtarnir~rrrIt.s in lubricated rolling bearing.~ is (I rrrrijor cr1~1.s~ of /~rel~rrrti~re failure, for exarnple by fatigue or I J ~ rrbr(r.sive rt~erlr of rolling el en rent.^, races or cages. However; tlre brtrotluctiorr of rtruclr Irorcler ceranzic (u.sually silicon nitride) balls or r01ler.s rurrrrirrg rlgnirzst steel races, in tlre lzybrid bearing concept, is like...

2018
Paul Dallyn Ashraf El-Hamalawi Alessandro Palmeri

The paper provides a critical appraisal of the events surrounding the unexpected settlement of large-diameter monopile foundations for offshore wind energy converters, and will detail experimentation that is to be undertaken to determine the extent of the wear failure mode in such structures. The potential for wear deterioration at the grout-steel interface has been caused by the lack of axial ...

Journal: :Materials Research-ibero-american Journal of Materials 2021

Plasma nitriding is a plasma-activated thermochemical method widely used to increase the fatigue strength, hardness and wear resistance of low-alloy steels. In this work, new structure consisting hollow cathode metal plate can produce discharge heat workpiece by radiation. This principle perform source plasma (HCSPN). Herein, 42CrMo steels were treated conventional (CPN) HCSPN treatments. The n...

2014

The major needs in machining are high material removal rate, good work surface finish and low tool wear. These objectives can be achieved by reducing tool wear using proper cutting fluid during machining.The effect of some cutting fluids namely: Mentholated spirit, paraffin, and soluble oil on the flank wear of High-speed steel and carbide tipped tools by orthogonal cutting has been studied. Ce...

2017
F. Stott D. Mitchell

Advanced carbon dioxide-cooled nuclear reactor environments can be tribologically hostile, with steel components sliding in contact at high temperatures. Although wearprotective oxides can reduce damage in the steady-state conditions, severe wear can occur in the early stages, particularly at temperatures of 300 to 500 "C, where oxidation rates may be low. In this paper, results are presented o...

2017
Vlad Cârlescu Dumitru N. Olaru Gheorghe Prisacaru Cezar Oprisan José Machado

In this paper, the authors present a new methodology to study the viscoelastic behaviour of the human finger. The methodology is based on experimental research consisting of a finger's indentation with a small steel cylindrical object for various indentation speeds. The tests were realized on a CETR UMT-2 Tribometer for indentation speed between 0.02 mm/s and 4 mm/s with a normal load of up to ...

A. Azizi, R. Rooki, S.Z. Shafaei,

Nowadays steel balls wear is a major problem in mineral processing industries and forms a significant part of the grinding cost. Different factors are effective on balls wear. It is needed to find models which are capable to estimate wear rate from these factors. In this paper a back propagation neural network (BPNN) and multiple linear regression (MLR) method have been used to predict wear rat...

نمودار تعداد نتایج جستجو در هر سال

با کلیک روی نمودار نتایج را به سال انتشار فیلتر کنید