A low magnetic Zr-1Mo alloy was fabricated by a powder bed fusion (PBF) process using a fiber laser. The microstructure, surface morphology, and pore distribution of the as-built Zr-1Mo alloy were observed. Its magnetic susceptibility and Vickers hardness were evaluated by magnetic susceptibility balance and a microindentation tester, respectively. The as-built Zr-1Mo alloy mainly consisted of ...

The effects of Nb and Pd on the electrochemical properties of a Ti-Ni hydrogen-storage electrode are studied. The results show that adding Pd or Nd to the alloy can slow down the rate of decay of the exchange current during charge-discharge cycling and is also useful in increasing the discharge capacity and cycle life of Ti-Ni electrodes. CC 1998 Elsevier Science S.A. Kqword.c: Alloy; Hydrogen ...

Control of microstructure parameters that affecting the Al-Ti-C master alloys grain refining efficiency is leading to improve the aluminum grain refinement. This study was an attempt to produce Al-Ti-C master alloys that provide these controlling factors with relying on the solute effect theory. The produced master alloys were examined by using scanning electron microscopy (SEM), energy-dispers...

© 2016 The Author(s). Published by Taylor & Francis on behalf of the Nordic Orthopedic Federation. This is an Open Access article distributed under the terms of the Creative Commons Attribution-Non-Commercial License (https://creativecommons.org/licenses/by-nc/3.0) DOI 10.3109/17453674.2015.1128780 (McGrory et al. 2015, Bishop et al. 2013). No mechanical implant failures (i.e. fractures) have b...

Effect of carbon and Ti on 7-s martensitic transformation behavior and damping capacity has been investigated in an Fe-17Mn alloy. The suppressive force of carbon against 7-s transformation increases linearly with an increase in carbon content, lowering M, temperature and volume fraction of s martensite. Carbon deteriorates damping capacity by reducing the area of y l e interfaces and by decrea...

In present work, prediction the effect of nose radius, rz (mm) on the equivalent strain (PEEQ) and surface finish during the machining of titanium alloy (Ti-6Al-4V) through orthogonal cutting process. The results were performed at several of the nose radiuses, rz (mm) while the cutting speed, vc (m/min), feed rate, f (mm/tooth) and depth of cut, d (mm) were remained constant. The equivalent pla...

Ceramometal bond strength has played an important role for the replacement of gold alloys by nickel-chromium alloys in dentistry. This study evaluated the metal/porcelain bond strength of three ceramic systems (Vita VMK 88, Williams and Duceram) associated with three nickel-chromium alloys (Durabond, Lite Cast B and Resistal P) and one experimental cobalt-chromium-titanium alloy. Thirty cast cy...

The in situ tensile straining of cross-sectional specimens inside a TEM is intrinsically very difficult to perform despite its obvious interest to study interfaces of surface treated materials. We have combined a FIB-based method to produce H-bar specimens of a nitrided Ti-6Al-4V alloy and in situ TEM straining stage, to successfully study the plastic deformation mechanisms that are activated c...

The durability of titanium (Ti) alloys bonded with high temperature adhesives such as polyimides has failed to attain the level of performance required for many applications. The problem to a large part is attributed to the instability of the surface treatment on the Ti substrate. Although Ti alloy adhesive specimens with surface treatments such as chromic acid anodization, Pasa-Jell, Turco, et...

Three different implants, bare Ti-6Al-4V alloy, Ti-6Al-4V alloy coated with plasma-sprayed hydroxyapatite (PSHA), and Ti-6Al-4V alloy coated with electrochemically deposited hydroxyapatite (EDHA), were implanted into canine trabecular bone for 6 h, 7, and 14 days, respectively. Environmental scanning electron microscopy study showed that PSHA coatings had higher bone apposition ratios than thos...