نتایج جستجو برای: weld microstructure
تعداد نتایج: 45350 فیلتر نتایج به سال:
In this investigation the effect of oxides powders of SiO2, MoO3 and CuO on the depth of penetration, microstructure and hardness profile of GTAWeld precipitation hardening martensitic 17-4PH was assessed. Samples were taken from 17-4PH steel sheet with the dimensions of 150*50 mm and with the thickness of 5 mm, and were welded by oxide powder of SiO2, MoO3 and CuO. Results showed that using ox...
In the present study, the microstructure of welded zone of Hastelloy X sheets with thickness of 1 mm via pulsed Nd-YAG laser welding were studied. This welding process was done by autogenus and conductive method. Microstructure were observed by metallurgical OM and SEM. Results shown Solidification of the weld metal is dendritic. The dendrites in the central zone of the welding are fine and equ...
In this research, two different filler metals, ERNiCrMo-3 and ER309L, were used for developing different microstructure, austenite (γ) and austenite and ferrite (γ+δ) in the weld metal and fatigue properties of welded samples were evaluated in the air and sea water environments. Microstructural studies indicated a good agreement between predicted microstructures via schiffler diagram and metall...
In this research, two different filler metals, ERNiCrMo-3 and ER309L, were used for developing different microstructure, austenite (γ) and austenite and ferrite (γ+δ) in the weld metal and fatigue properties of welded samples were evaluated in the air and sea water environments. Microstructural studies indicated a good agreement between predicted microstructures via schiffler diagram and metall...
Measurement of the effects of helium (from tritium decay) on the weldability of Types 304 and ITER Grade 316LN stainless steel demonstrated the inherent complexities in designing and conducting an experimental program using tritium-charged-and-aged materials to simulate the effects of irradiation-induced helium on weld behavior. Differences in microstructure, surface condition and alloy chemist...
The effective assessment of the integrity of welds is a complicated NDE problem that continues to be a challenge. To be able to completely characterize a weld, detailed knowledge of its tensile strength, ductility, hardness, microstructure, macrostructure, and chemical composition is needed. NDE techniques which can provide information on any of these features are extremely important. In this p...
For hot extrusions of magnesium alloy sheets, Dissimilar AZ80 and AZ31 were used, in which AZ80 was placed on advancing side and AZ31 on retreating side, using friction stir butt welding with different process parameters. Some defect-free welded joints with good weld surfaces could be obtained with some suitable welding conditions. The maximum tensile strength of welded joint which is 225.5 MPa...
The vast majority of steel weld deposits solidify under highly nonequilibrium cooling conditions. A consequence of this is the chemical segregation of substitutional alloying elements during solidification, a segregation that persists as the weld cools to ambient temperature. Solidification-induced segregation of interstitials is usually not a problem due to the ease with which they can diffuse...
Three-dimensional chemical analysis of laser-welded NiTi–stainless steel wires using a dual-beam FIB
The biomedical industry has an increasing demand for processes to join dissimilar metals, such as laser welding of NiTi and stainless steel wires. A region of the weld close to the NiTi interface, which previously was shown to be prone to cracking, was further analyzed by energy dispersive spectrometry (EDS) extended in the third dimension using a focused ion beam. As the spatial resolution of ...
نمودار تعداد نتایج جستجو در هر سال
با کلیک روی نمودار نتایج را به سال انتشار فیلتر کنید