The crystallization behavior of poly(ε-caprolactone) (PCL) in a poly(vinylidene fluoride) (PVDF)/PCL blend as well as on a highly orientated PVDF substrate was studied by means of POM, DSC and TEM. The results show that the miscibility of the PVDF/PCL blend and the spherulitic morphology of PVDF varies with the blend ratio. For all the compositions, the pre-existing PVDF crystals accelerated th...

Polyvinylidene fluoride (PVDF) ultrafiltration (UF) membrane combined with polyvinylidene fluoride-graft-2-hydroxyethyl acrylate (PVDF-g-PHEA) was fabricated via non-solvent induced phase separation (NIPS). In this study, PVDF-g-PHEA was synthesized via atom transfer radical polymerization (ATRP) method, and then synthesized graft copolymer was characterized using Fourier transform infrared spe...

This work describes the thermal stability and magnetic properties of polyvinylidene fluoride (PVDF)/magnetite nanocomposites fabricated using the solution mixing technique. The image of transmission electron microscopy for PVDF/magnetite nanocomposites reveals that the 13 nm magnetite nanoparticles are well distributed in PVDF matrix. The electroactive β-phase and piezoelectric responses of PVD...

TiO₂/g-C₃N₄/PVDF composite membranes were prepared by a phase inversion method. A comparison of the performance and morphology was carried out among pure PVDF, g-C₃N₄/PVDF, TiO₂/PVDF and TiO₂/g-C₃N₄/PVDF composite membranes. The results of permeability and instrumental analysis indicated that TiO₂ and g-C₃N₄ organic-inorganic composites obviously changed the performance and structure of the PVD...

Poly(vinylidene fluoride) (PVDF) and poly(butylene succinate-co-butylene adipate) (PBSA) are crystalline/crystalline polymer blends with PVDF being the high-T(m) component and PBSA being the low-T(m) component, respectively. PVDF/PBSA blends are miscible as shown by the decrease of crystallization peak temperature and melting point temperature of each component with increasing the other compone...

Melting and crystallization of poly(vinylidene fluoride) (PVDF) blended with polyamide 6 (PA6) has been studied by differential scanning calorimetry. The melting of PVDF and PA6 is observed over a small temperature range, i.e. 174 to 181°C and 220 to 230°C, respectively, over the whole blend composition. This observation indicates that PVDF and PA6 are immiscible and do not co-crystallize, alth...

In this study, Polyvinylidene fluoride (PVDF) hollow fiber hemodialysis membranes were prepared by non-solvent induced phase separation (NIPS) with compound addtive. The compound additive was made with polyvinyl pyrrolidone (PVP) and Poly ethylene glycol (PEG). The results showed that the modified PVDF membrane had better separation performance than virgin PVDF membrane. The UF flux of modified...

Wide-angle X-ray scattering in conjunction with pole figure technique was used to study the texture of poly(vinylidene fluoride) (PVDF) α and γ phase crystals in nanolayered polysulfone/poly(vinylidene fluoride) films (PSF/PVDF) produced by layer-multiplying coextrusion. In all as-extruded PSF/PVDF films, the PVDF nanolayers crystallized into the α phase crystals. A large fraction of those crys...

Composite membranes were successfully prepared using a phase-inversion method. The X-ray powder diffraction (XRD) and energy dispersive X-ray (EDX) profiles has confirmed formation of 4.8 wt % Ag/poly(vinylidene fluoride-co-hexafluoropropene) (PVDF-HFP), 3 wt % Ag-MWCNTs/PVDF-HFP (EDX surface composition of Ag nanoparticles) and 1.5 wt % MWCNTs/PVDF-HFP composite membranes. The MWCNTs crystalli...

*Correspondence: Claudia Merlini and Guilherme Mariz de Oliveira Barra, Department of Mechanical Engineering, Universidade Federal de Santa Catarina, Campus Universitário Trindade, Caixa Postal 476, Florianópolis, Santa Catarina 88040-900, Brazil e-mail: dra.claudiamerlini@ yahoo.com.br; [email protected] Electrically conductive polyaniline (PANI)-coated electrospun poly(vinylidene fluoride) (PVD...