نتایج جستجو برای: Stainless Steel 304

تعداد نتایج: 89407  

Journal: :IJMMME 2011
Z. Y. Jiang D. B. Wei K. Tieu J. X. Huang A. W. Zhang X. Shi S. H. Jiao

The oxidation of stainless steels 304 and 304L during hot rolling is studied in this paper. Results show the oxide scale thickness decreases significantly with an increase of reduction, and the oxide scales of both 304 and 304L stainless steels were found more deformable than the steel substrate. Surface roughness shows a complicated transfer during the hot rolling process due to the complexity...

2001
F. Pedraza

Soft X-ray absorption spectroscopy (XAS) has been used to study the influence of Si ion implantation on the passive layer of AISI 304 stainless steel, as well as on its high-temperature oxidation behaviour. Ion implantation is a usual technique to improve the corrosion and oxidation resistance of steels. To study the effects of ion implantation on the room temperature corrosion behavior of AISI...

2016
Bibo Yao Zhaoyao Zhou Liuyang Duan Zhiyu Xiao

Powder metallurgy (P/M) technique is usually used for manufacturing porous metal materials. However, some P/M materials are limitedly used in engineering for their performance deficiency. A novel 304 stainless steel P/M material was produced by a solid-state sintering of 304 stainless steel powders and 304 short stainless steel fibers, which were alternately laid in layers according to mass rat...

2015
Wenquan Zhang Jinzhong Lu Kaiyu Luo Hugo F. Lopez

The effects of different laser shock peening (LSP) impacts on the three-dimensional displayed distributions of surface and in-depth residual stress at a laser spot of AISI 304 stainless steel were investigated by X-ray diffraction technology with the sin2φ method and MATLAB 2010a software. Microstructural evolution in the top surface subjected to multiple LSP impacts was presented by means of c...

1993
Daniel J. Rader Wayne M. Trott John R. Torczynski Jaime N. Castañeda T. W. Grasser Thomas W. Grasser

A previously-developed experimental facility has been used to determine gas-surface thermal accommodation coefficients from the pressure dependence of the heat flux between parallel plates of similar material but different surface finish. Heat flux between the plates is inferred from measurements of temperature drop between the plate surface and an adjacent temperaturecontrolled water bath. The...

Journal: :Journal of acupuncture and meridian studies 2010
Hye Suk Hwang Eun Jin Yang Yeon Hee Ryu Myeong Soo Lee Sun-Mi Choi

We present the first investigation of electrical corrosion in acupuncture needles after electrical stimulation. Using scanning electron microscopy, we observed the occurrence of electrochemical corrosion on the surface of stainless steel 304 acupuncture needles after electrical stimulation in the tibial muscles of rats. Biphasic pulse electrical stimuli with 10-Hz frequency, 1-mA intensity and ...

2013
N. Siva Shanmugam G. Buvanashekaran K. Sankaranarayanasamy

In this research work, investigations are carried out on Continuous Wave (CW) Nd:YAG laser welding system after preliminary experimentation to understand the influencing parameters associated with laser welding of AISI 304. The experimental procedure involves a series of laser welding trials on AISI 304 stainless steel sheets with various combinations of process parameters like beam power, beam...

2017
Elaine Black Krista Owens Richard Staub Junzhong Li Kristen Mills Justin Valenstein John Hilgren

Disinfectants play an important role in controlling microbial contamination on hard surfaces in hospitals. The effectiveness of disinfectants in real life can be predicted by laboratory tests that measure killing of microbes on carriers. The modified Quantitative Disk Carrier Test (QCT-2) is a standard laboratory method that employs American Iron and Steel Institute (AISI) Type 430 stainless st...

2010
D. PHILIP SELVARAJ P. CHANDRAMOHAN D. P. Selvaraj P. Chandramohan

The present work is concentrated with the dry turning of AISI 304 Austenitic Stainless Steel (ASS). This paper presents the influence of cutting parameters like cutting speed, feed rate and depth of cut on the surface roughness of austenitic stainless steel during dry turning. A plan of experiments based on Taguchi’s technique has been used to acquire the data. An orthogonal array, the signal t...

2016
J. Childress S. Liou C. Chien C. L. Chien

Ordinary 304 stainless steel has a fcc structure and is non-magnetic at room temperature. By using a vapor quenching method, we have fabricated single-phase metastable bcc 304 stainless steel which is strongly ferromagnetic with a magnetization of 130 emu/g and a Curie temperature in excess of 550 OC. Upon subsequent annealing above 550 OC, the metastable bcc state transforms back into the usua...

نمودار تعداد نتایج جستجو در هر سال

با کلیک روی نمودار نتایج را به سال انتشار فیلتر کنید